TEAC AI-303 Owners Manual English Francais Espanol - Page 7

Before use, Using the remote control, Precautions for use, Installing batteries

Get TEAC AI-303 PDF manuals and user guides View all TEAC AI-303 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Before use Using the remote control VV Placement precautions oo Do not install this unit in a location that could become hot. This includes places that are exposed to direct sunlight or near a radiator, heater, stove or other heating equipment. Moreover, do not place it on top of an amplifier or other equipment that generates heat. Doing so could cause discoloration, deformation or malfunction. oo You may stack this unit with a PD-301 or UD-301. However, place this unit on top in order to improve heat dissipation. oo When installing this unit, leave a little space (at least 5 cm or 2") between it and walls and other devices in order to allow good heat dissipation. If you put it in a rack, for example, leave at least 5 cm (2") open above and 10 cm (4") open behind it. Failure to provide these gaps could cause heat to build up inside and result in fire. Maintenance Wipe dirt from the top cover and other panel surfaces using a soft cloth that has been slightly dampened with a diluted neutral cleanser. Do not wipe with chemical cleaning cloths, thinner or other chemical agents. Doing so could damage the surface. Precautions for use VVMisuse of batteries could cause them to rupture or leak, which might result in fire, injury or the staining of nearby materials. Please carefully read and observe the precautions on page 3. oo When using the remote control, point it toward the remote control signal receiver on the main unit from a distance of 5 m (16 ft) or less. Do not place obstructions between the main unit and the remote control. oo When not using the remote control for an extended period of time, remove the batteries to prevent leakage. Installing batteries Remove the cover from the back of the remote control and insert two AAA batteries with their ¥/^ oriented as shown in the case. Replace the cover. VV For your safety, disconnect the power cord from the outlet before cleaning. When to replace batteries If the distance required between the remote and the main unit decreases or if the unit stops responding to the remote buttons, replace both batteries with new ones. Dispose of the used batteries according to the instructions on them or requirements set by your local municipality. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
7
Using the remote control
Precautions for use
V
Misuse of batteries could cause
them to rupture or leak, which
might result in fire, injury or the
staining of nearby materials.
Please carefully read and observe
the precautions on page 3.
o
When using the remote control, point it toward the
remote control signal receiver on the main unit from a
distance of 5 m (16 ft) or less. Do not place obstructions
between the main unit and the remote control.
o
When not using the remote control for an extended
period of time, remove the batteries to prevent leakage.
Installing batteries
Remove the cover from the back of the remote control and
insert two AAA batteries with their
¥
/
^
oriented as shown
in the case. Replace the cover.
When to replace batteries
If the distance required between the remote and the main
unit decreases or if the unit stops responding to the remote
buttons, replace both batteries with new ones.
Dispose of the used batteries according to the instructions
on them or requirements set by your local municipality.
V
Placement precautions
o
Do not install this unit in a location that could become
hot. This includes places that are exposed to direct
sunlight or near a radiator, heater, stove or other heat-
ing equipment. Moreover, do not place it on top of
an amplifier or other equipment that generates heat.
Doing so could cause discoloration, deformation or
malfunction.
o
You may stack this unit with a PD-301 or UD-301.
However, place this unit on top in order to improve heat
dissipation.
o
When installing this unit, leave a little space (at least
5  cm or 2
"
) between it and walls and other devices in
order to allow good heat dissipation.
If you put it in a rack, for example, leave at least 5 cm (2
"
)
open above and 10 cm (4
"
) open behind it.
Failure to provide these gaps could cause heat to build
up inside and result in fire.
Maintenance
Wipe dirt from the top cover and other panel surfaces using
a soft cloth that has been slightly dampened with a diluted
neutral cleanser.
Do not wipe with chemical cleaning cloths, thinner or other
chemical agents. Doing so could damage the surface.
V
For your safety, disconnect the power cord
from the outlet before cleaning.
Before use