TP-Link T2600G-28SQ T2600G Series Switches CLI Reference Guide Guide
TP-Link T2600G-28SQ Manual
View all TP-Link T2600G-28SQ manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T2600G-28SQ manual content summary:
- TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 1
CLI Reference Guide T2600G-18TS /T2600G-28TS (TL-SG3424) /T2600G-28TS-DC/ T2600G-28MPS (TL-SG3424P) / T2600G-28SQ/ T2600G-52TS (TL-SG3452) 1910012658 REV4.2.0 December 2019 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 3
...24 configure...25 exit ...26 end ...26 clipaging...27 history ...27 history clear ...28 Charpter 4. User Management Commands 29 4.1 user name (password) ...29 4.2 user name (secret) ...30 4.3 service password-recovery ...31 4.4 show user account-list ...32 4.5 show user configuration ...33 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 4
manual...34 system-time ntp...34 system-time dst predefined...36 system-time dst date...37 system-time dst recurring ...38 hostname...39 location ...40 contact-info ...40 ip address ...41 ip address-alloc...42 reset...43 service reset remove backup-image ...51 firmware upgrade ...51 boot autoinstall - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 5
cable-diagnostics interface 62 show cpu-utilization...62 show memory-utilization ...63 show temperature ...63 show voltage ...64 Charpter 6. EEE Configuration Commands 65 6.1 eee...65 6.2 show interface eee ...65 Charpter 7. SDM Template Commands 67 7.1 sdm prefer ...67 7.2 show sdm prefer - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 6
ddm shutdown ...93 ddm temperature_threshold...93 ddm voltage_threshold ...94 ddm bias_current_threshold...95 ddm tx_power_threshold ...96 ddm rx_power_threshold ...97 show ddm configuration ...98 show ddm status ...99 Charpter 13. Etherchannel Commands 100 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 7
-count 110 14.7 mac address-table notification (interface 112 14.8 mac address-table security (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 113 14.9 mac address-table vlan-security (For T2600G-18TS 114 14.10 show mac address-table ...115 14.11 clear mac address-table...115 14 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 8
Charpter 17. Protocol-based VLAN Commands 132 17.1 17.2 17.3 17.4 17.5 protocol-vlan template...132 protocol-vlan vlan ...133 protocol-vlan group...134 show protocol-vlan template 134 show protocol-vlan vlan...135 Charpter 18. Private VLAN Commands 136 18.1 18.2 18.3 18.4 18.5 18.6 18.7 18.8 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 9
Charpter 21. IGMP Snooping Commands 156 21.1 21.2 21.3 21.4 21.5 21.6 21.7 21.8 21.9 21.10 21.11 21.12 21.13 21.14 21.15 21.16 21.17 21.18 21.19 21.20 21.21 21.22 21.23 21.24 21.25 21.26 21.27 ip igmp snooping (global) ...156 ip igmp snooping version ...156 ip igmp snooping drop-unknown 157 ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 10
.10 debug spanning-tree ...203 spanning-tree (global)...204 spanning-tree (interface)...204 spanning-tree common-config 205 spanning-tree mode...206 spanning-tree mst configuration 207 instance...207 name ...208 revision ...209 spanning-tree mst instance ...210 IX - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 11
24.11 24.12 24.13 24.14 24.15 24.16 24.17 24.18 24.19 24.20 24.21 24.22 24.23 24.24 24.25 24.26 24.27 spanning-tree mst...210 spanning-tree priority ...211 spanning-tree timer...212 spanning-tree hold-count ...213 spanning-tree max-hops ...213 spanning-tree bpdufilter...214 spanning-tree bpduflood - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 12
...255 show ipv6 interface ...255 show ipv6 route...256 show ipv6 route summary...256 Charpter 29. IPv6 Address Configuration Commands 258 29.1 29.2 29.3 29.4 29.5 ipv6 enable ...258 ipv6 address autoconfig ...259 ipv6 address link-local...259 ipv6 address dhcp...260 ipv6 address ra ...261 XI - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 13
.2 31.3 31.4 31.5 31.6 31.7 31.8 31.9 31.10 31.11 31.12 31.13 31.14 31.15 31.16 31.17 31.18 service dhcp server ...274 ip dhcp server extend-option capwap-ac-ip 274 ip dhcp server extend-option vendor-class-id 275 ip dhcp server exclude - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 14
pool ...287 show ip dhcp server excluded-address 288 show ip dhcp server manual-binding 288 show ip dhcp server binding ...289 clear ip dhcp server statistics 32.3 32.4 32.5 32.6 32.7 32.8 32.9 32.10 32.11 32.12 service dhcp relay ...291 ip dhcp relay hops ...291 ip dhcp relay time ...292 ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 15
qos cos-map ...313 34.10 show qos dot1p-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 313 34.11 show qos dot1p-remap (For T2600G-18TS 314 34.12 show qos dscp-map interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 314 34.13 show qos dscp-map (For - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 16
-protocol ...345 ip http secure-ciphersuite ...346 ip http secure-max-users...347 ip http secure-session timeout 348 ip http secure-server download certificate 348 ip http secure-server download key 349 show ip http configuration ...350 show ip http secure-server ...351 Charpter 40. SSH Commands - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 17
40.8 40.9 remove public-key ...356 show ip ssh ...357 Charpter 41. Telnet Commands 358 41.1 41.2 41.3 41.4 telnet ...358 telnet enable...358 telnet port ...359 show telnet-status ...359 Charpter 42. Serial Port Commands 361 42.1 serial_port baud-rate ...361 Charpter 43. AAA Commands 362 43 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 18
43.28 enable-admin ...382 Charpter 44. IEEE 802.1x Commands 384 44.1 44.2 44.3 44.4 44.5 44.6 44.7 44.8 44.9 44.10 44.11 44.12 44.13 44.14 44.15 44.16 44.17 44.18 dot1x system-auth-control ...384 dot1x handshake ...385 dot1x auth-protocol ...385 dot1x vlan-assignment ...386 dot1x accounting ... - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 19
47.9 47.10 47.11 47.12 47.13 47.14 47.15 47.16 47.17 47.18 47.19 access-list action ...414 redirect ...415 s-condition ...416 s-mirror...417 qos-remark ...417 access bind...418 show access-list ...419 show access-list bind ...419 show access-list status ...420 show access-list counter ...420 clear - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 20
Charpter 51. IPv6 Verify Source Commands 440 51.1 51.2 51.3 ipv6 verify source ...440 show ipv6 verify source ...441 show ipv6 verify source interface 441 Charpter 52. DHCPv4 Filter Commands 443 52.1 52.2 52.3 52.4 52.5 52.6 52.7 52.8 52.9 ip dhcp filter ...443 ip dhcp filter (interface) ... - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 21
show ethernet-oam configuration 474 show ethernet-oam event-log 475 show ethernet-oam statistics 475 show ethernet-oam status ...476 Charpter 57. DLDP Commands 477 57.1 57.2 57.3 57.4 57.5 57.6 57.7 57.8 dldp (global) ...477 dldp interval ...477 dldp shut-mode...478 dldp reset (global)...479 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 22
495 snmp-server traps power...496 snmp-server traps link-status 497 rmon history ...498 rmon event ...499 show snmp-server group ...503 show snmp-server user ...504 show snmp-server community 504 show snmp- inline ...514 show power inline configuration interface 514 show power inline information - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 23
60.6 60.7 60.8 60.9 60.10 60.11 60.12 ip arp inspection burst-interval 520 ip arp inspection recover ...521 show ip arp inspection...522 show ip arp inspection interface 522 show ip arp inspection vlan ...523 show ip arp inspection statistics 523 clear ip arp inspection statistics 524 Charpter - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 24
about CLI (Command Line Interface). The device mentioned in this Guide stands for T2600G-18TS/T2600G-28TS/T2600G-28TS-DC/T2600G-28MPS/T2600G-28SQ/ T2600G-52TS JetStream Gigabit L2 Managed Switch without any explanation. The commands in this guide apply to these models if not specially noted, and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 25
(Digital Diagnostic Monitoring) function. Chapter 13: Etherchannel Commands Provide information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). Chapter 14: MAC Address Commands Provide information about the commands used for Address - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 26
28: Static Routes Commands Provide information about the commands used for configuring the Static Route function. Chapter 29: IPv6 Address Configuration Commands Provide information about the commands used for configuring the System IPv6 addresses. Chapter 30: ARP Commands Provide information about - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 27
Chapter 39: HTTP and HTTPS Commands Provide information about the commands used for configuring the HTTP and HTTPS logon. Chapter 40: SSH Commands Provide information about the commands used for configuring and managing SSH (Security Shell). Chapter 41: Telnet Commands Provide information about the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 28
Protocol) functions. Chapter 59: PoE Commands (For T2600G-28MPS only) Provide information about the commands used for configuring PoE function. Chapter 60: ARP Inspection Commands Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack. Chapter 61 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 29
If you are using the switch's Micro-USB console port with the USB port of a Windows PC, a driver for the USB port is required. The USB driver is provided on the resource CD. Follow the InstallSheild Wizard to accomplish the installation. The TP-Link USB Console Driver supports the following Windows - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 30
the TP-Link USB Console Driver is installed, the PC's USB port will act as RS-232 serial port when the PC's USB port is connected to the switch's Micro Ports ->USB Serial Port. Figure 1-1 USB Serial Port Number 4. Configure the terminal emulation program or the terminal to use the following settings - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 31
"T2600G-28TS>" will appear indicating that you have successfully logged in to the switch and you can use the CLI now. Figure 1-2 Log in to the Switch Note: The first time you log in, change the password to better protect your network and devices. 1.1.2 Logon by Telnet The switch supports - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 32
as Figure 1-4, and press the Enter button. Figure 1-4 Connect to the Switch 3. Type the default user name and password (both of them are admin), then press the Enter button so as to enter User EXEC Mode. Figure 1-5 Enter into the User EXEC Mode Note: The first time you log in, change the password - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 33
1-6 Enter into the Privileged EXEC Mode Now you can manage your switch with CLI commands through Telnet connection. Note: You can refer to Chapter 4 User Management Commands for detailed commands information of the Telnet connection configuration. 1.1.3 Logon by SSH To log on by SSH, a Putty client - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 34
in the Port field; select SSH as the Connection type. Figure 1-8 SSH Connection Configuration 2. Click the Open button in the above figure to log on to the switch. Enter the login user name and password to log on the switch, and then enter enable to enter Privileged EXEC Mode, so you can continue to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 35
■ Key Authentication Mode 2. Select the key type and key length, and generate SSH key. Figure 1-10 Generate SSH Key Note: 1. The key length is in the range of 512 to 3072 bits. 2. During the key generation, randomly moving the mouse quickly can accelerate the key generation. 12 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 36
is successfully generated, please save the public key and private key to a TFTP server. Figure 1-11 Save the Generated Key 4. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows: Figure 1-12 Download the Public Key 13 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 37
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading cannot be interrupted. 5. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login. Figure 1-13 SSH Connection Configuration 14 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 38
to the switch without entering password, it indicates that the key has been successfully downloaded. Figure 1-15 Log on the Switch 1.2 CLI Command Modes The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 39
Interface Configuration Mode can also be divided into Interface Ethernet, Interface link-aggregation switch. Use the enable command to access Privileged EXEC mode. T2600G-28TS# Enter the disable or the exit command to return to User EXEC mode. Enter configure command to access Global Configuration - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 40
mode. T2600G-28TS (config-vlan)# Use the end command or press Ctrl+Z to return to Privileged EXEC mode. Enter the exit command or the # command to return to Global configuration mode. Note: 1. The user is automatically in User EXEC Mode after the connection between the PC and the switch is - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 41
parameters for the vlan-port. ■ VLAN Configuration Mode: In this mode, users can create a VLAN and add a specified port to the VLAN. 3. Some commands are global, that means they can be performed in all modes: ■ show: Display all information of switch, for example: statistic information, port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 42
■ Italic Font indicates a variable (an actual value must be assigned). For example: bridge aging-time aging-time 1.4.2 Special Characters You should pay attentions to the Description below if the variable is a character string: ■ These six characters" < > , \ & cannot be input. ■ If a blank is - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 43
rest can be done on the same manner. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enter the Console port configuration mode and configure the console port 0: T2600G-28TS(config)#line console 0 Enter the Virtual Terminal - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 44
rj45 command is used to configure the console media type as RJ-45 for input. The switch has two console ports available Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the RJ-45 console input: T2600G-28TS(config)# line console 0 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 45
access Privileged EXEC Mode from User EXEC Mode: T2600G-28TS>enable Enter password: T2600G-28TS# 3.2 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the configuration is written, using the symmetric - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 46
Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the global encryption function: T2600G-28TS(config)# service you can copy from another switch's configuration file. After the encrypted password is configured, you should use the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 47
configured password will take effect. Example Set the super password as "admin" and unencrypted to access Privileged EXEC Mode from User EXEC Mode: T2600G which you can copy from another switch's configuration file. After the encrypted password is configured, you should use the corresponding - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 48
Mode from Privileged EXEC Mode. Syntax configure Command Mode Privileged EXEC Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Access Global Configuration Mode from Privileged EXEC Mode: T2600G-28TS# configure T2600G-28TS(config)# 25 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 49
Privileged EXEC Mode: T2600G-28TS(config-if)# exit T2600G-28TS(config)#exit T2600G-28TS# 3.7 end Description The end command is used to return to Privileged EXEC Mode. Syntax end Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 50
show the latest 20 commands you entered in the current mode since the switch is powered. Syntax history Command Mode Privileged EXEC Mode and any Configuration Mode Privilege Requirement None. Example Show the commands you have entered in the current mode: T2600G-28TS (config)# history 1 history 27 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 51
not be shown next time you use the history command. Syntax history clear Command Mode Privileged EXEC Mode and any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear the commands you have entered in the current mode - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 52
switch from being randomly changed. 4.1 user name (password) Description The user name command is used to add a new user or modify the existed users' information. To delete the existed users, please use no user fixed length, which you can copy from another switch's configuration file. After the 29 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 53
re-enter this mode. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 54
, only the latest configured password will take effect. Example Add and enable a new admin user named "tplink", of which the password is "admin". The password will be displayed in the encrypted form. T2600G-28TS(config)#user name tplink privilege admin secret 0 admin 4.3 service password-recovery - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 55
the switch after its startup. Syntax service password-recovery no service password-recovery Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the switch's password-recovery feature: T2600G-28TS(config)# service password - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 56
including access-control, max-number and the idle-timeout, etc. Syntax show user configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the security configuration information of the users: T2600G-28TS(config)# show user configuration 33 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 57
the System information and System IP, reboot and reset the switch, upgrade the switch system and other operations. 5.1 system-time manual Description The system-time manual command is used to configure the system time manually. Syntax system-time manual time Parameter time -- Set the date and time - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 58
The detailed information that each time-zone means are displayed as follow: UTC-12:00 -- TimeZone for International Date Line West. UTC-11:00 -- TimeZone for Coordinated Universal Time-11. UTC-10:00 -- TimeZone for Hawaii. UTC-09:00 -- TimeZone for Alaska. UTC-08:00 -- TimeZone for Pacific Time - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 59
Admin and Operator level users have access to these commands. Example Configure the system time mode as NTP, the time zone is UTC-12:00, the primary NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163, the fetching-rate is 11 hours: T2600G-28TS(config)# system-time - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 60
Only Admin and Operator level users have access to these commands. Example Configure the daylight saving time as USA standard: T2600G-28TS(config)#system-time dst predefined USA 5.4 system-time dst date Description The system-time dst date command is used to configure the one-off daylight saving - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 61
Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the daylight saving time from zero clock, Apr 1st to zero clock Oct 1st and the offset is 30 minutes in 2015: T2600G-28TS(config)# system-time dst date Apr 1 00:00 2015 Oct 1 00 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 62
Name. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example "T2600G-28TS". Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the system name as TPLINK: 39 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 63
is used to configure the system contact information. To clear the system contact information, please use no contact-info command. Syntax contact-info [ contact_info ] no contact-info Parameter contact_info -- Contact Information. It consists of 32 characters at most. It is "www.tp-link.com" by - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 64
users have access to these commands. Example Configure the system contact information as www.tp-link.com: T2600G-28TS(config)# contact-info www.tp-link.com 5.9 ip address Description This ip address command is used to configure the IP address and IP subnet mask for the specified interface manually - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 65
Server. bootp -- Specify the Layer 3 interface to obtain IP address from the BOOTP Server. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Client function on the Lay 3 routed port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 66
Privilege Requirement Only Admin level users have access to these commands. Example Reset all settings of the switch except its IP address: T2600G-28TS# reset except-ip 5.12 service reset-disable Description The service reset-disable command is used to disable the reset function of the console port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 67
T2600G-28TS(config)# service reset-disable 5.13 reboot Description The reboot command is used to reboot the Switch. To avoid damage, please don't turn off the device while rebooting. Syntax reboot Command Mode Privileged EXEC Mode Privilege Requirement Only Admin level users have access to these - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 68
the time that this command is executed, the switch will reboot later that day; otherwise the switch will reboot at the time point the next day. Example Specify the switch to save the configuration files and reboot in 200 minutes, T2600G-28TS(config)# reboot-schedule in 200 save_before_reboot 5.15 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 69
and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. name -- Specify the name for the configuration file which would be users have access to these commands. Example Backup the configuration files to TFTP server with the IP 192.168.0.148 and name this file config.cfg: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 70
. Command Mode Privileged EXEC Mode Privilege Requirement Only Admin level users have access to these commands. Example Download the configuration file named as config.cfg to the switch from TFTP server with the IP 192.168.0.148: T2600G-28TS# copy tftp startup-config ip-address 192.168.0.148 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 71
Privilege Requirement Only Admin level users have access to these commands. Example Export the backup configuration file of the switch to the TFTP server with the IP 192.168.0.148 and name the file config.cfg: T2600G-28TS# copy backup-config tftp ip-address 192.168.0.148 filename config 5.19 copy - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 72
and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. name -- Specify the name for the configuration file which would be downloaded users have access to these commands. Example Download the configuration file named config.cfg from the TFTP server with the IP 192.168.0.148: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 73
of the image, either startup image or backup image. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the image2.bin as the startup image: T2600G-28TS(config)# boot application filename image2 startup 5.23 boot config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 74
users have access to these commands. Example Configure the config2.cfg as the startup image: T2600G- users have access to these commands. Example Delete the backup image file: T2600G-28TS# remove backup-image 5.25 firmware upgrade Description The firmware upgrade command is used to upgrade the switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 75
users have access to these commands. Example Upgrade the switch's backup image file with the file firmware.bin in the TFTP server with the IP address 192.168.0.148, and reboot the switch with this firmware: T2600G-28TS# firmware no boot autoinstall start Command Mode Global Configuration Mode 52 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 76
boot autoinstall persistent-mode. Syntax boot autoinstall persistent-mode no boot autoinstall persistent-mode Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Start Auto Install function: T2600-28TS(config)# boot autoinstall - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 77
. Syntax boot autoinstall auto-reboot no boot autoinstall auto-reboot Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the switch to auto reboot after Auto Install function completed successfully: T2600-28TS(config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 78
-- The count of retrying auto install. The value ranges from 1 to 3. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure TFTP retry 2 times when download files failed: T2600- 28TS(config)# boot autoinstall retry-count - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 79
configuration file which downloaded by Auto Install: T2600-28TS# show boot autoinstall downloaded-config 5.33 ping Description The ping command is used to test the connectivity between the switch supported, switch and the network device is failed to establish: T2600G-28TS# ping 192.168.0.131 -n 8 -l - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 80
supported users have access to these commands. Example Test the connectivity between the switch and the network device with the IP 192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 81
Device Location, System Contact, Hardware Version, Firmware Version, System Time, Run Time and so on. Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the system information: T2600G-28TS# show system-info 5.36 show image - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 82
system. Syntax show boot Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the system boot configuration information: T2600G-28TS# show boot 5.38 show running-config Description The show running - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 83
be lost the next time you reboot the switch. Syntax show startup-config Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the saved configuration: T2600G-28TS# show startup-config 5.40 show system - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 84
-time dst command is used to display the DST information of the switch. Syntax show system-time dst Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DST information of the switch: T2600G-28TS# show system-time dst 5.42 show system-time ntp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 85
the connection status of the cable connected to the switch, locate and diagnose the trouble spot of the network. Syntax show cable-diagnostics Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Show the cable-diagnostics of port 3: T2600G-28TS# show cable-diagnostics - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 86
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the memory utilization information of the switch: T2600G-28TS# show memory-utilization 5.46 show temperature Note: Only T2600G-28TS-DC supports this command. Description The show temperature - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 87
of the switch: T2600G-28TS-DC# show temperature 5.47 show voltage Note: Only T2600G-28TS-DC supports this command. Description The show voltage command is used to display the voltage of DC power board. Syntax show voltage Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 88
. Syntax eee no eee Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable EEE on port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#eee 6.2 show interface eee - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 89
Privilege Requirement None. Example Display the EEE configuration of each port T2600G-28TS# show interface eee 66 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 90
". enterpriseV6 -- Specify the SDM template used in the switch as "enterpriseV6". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Specify the SDM template as enterpriseV4: T2600G-28TS(config)# sdm prefer enterpriseV4 67 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 91
. enterpriseV6 -- Display the resource allocation of the enterpriseV6 template. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the resource allocation of the template currently in use, and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 92
Command Mode Global Configuration Mode Parameter name -- The time-range name, ranging from 1 to 16 characters. Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a time-range named "tRange1" for the switch: T2600G-28TS(config)# time - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 93
in the format of MM/DD/YYYY. Command Mode Time-range Create Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an absolute time-range for the switch and specify the date extending from May 5th, 2017 through Oct. 5th - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 94
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a time-range entry named "tRange3" and configure time-range to exclude the holiday: T2600G-28TS(config)#time-range tRange3 T2600G-28TS(config-time-range)#holiday exclude 71 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 95
used to create holiday for the switch. To delete the corresponding holiday configuration, please use no holiday command. User level users have access to these commands. Example Create a holiday named "holiday1" and configure the start date as October 1st and the end date as October 3rd: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 96
time range. Syntax show time-range [name ] Parameter name --Specify the time range name with 1 to 16 characters. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the defined time range: T2600G-28TS# show time-range 73 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 97
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example To enter the Interface gigabitEthernet Configuration Mode and configure port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 9.2 interface range gigabitEthernet Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 98
Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. User Guidelines Command range gigabitEthernet Configuration Mode, and configure ports 1, 2, 3, 6, 7 and 9 at the same time by adding them to one port-list: T2600G-28TS( - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 99
ranging from 1 to 16 characters. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / User level users have access to these commands. Example Add a Description Port_5 to port 1/0/5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 100
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Disable port 1/0/3: T2600G-28TS(config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 101
range port-channel) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the Duplex Mode as full-duplex for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# duplex full 9.7 jumbo-size Description The jumbo - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 102
. Example Configure the Speed Mode as 100Mbps for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# speed 100 9.9 serdes-mode (Only for Certain Devices) Note: Only T2600G-18TS, T2600G-28TS, T2600G-28TS-DC, T2600G-28MPS, T2600G-52TS support this command - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 103
port-channel) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure port 1/0/26 to collocate with electrical interface modules: T2600G-28TS(config)# interface gigabitEthernet 1/0/26 T2600G-28TS(config-if)# serdes-mode sgmii 9.10 clear counters - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 104
of all fiber ports. Syntax show fiber ports Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all fiber ports: T2600G-28TS(config)# show fiber ports 9.12 show interface status Description The show interface status command - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 105
-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the statistics information of all Ethernet ports and port channels: T2600G-28TS(config)# show interface counters Display the statistics information of port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 106
and Any Configuration Mode Privilege Requirement None. Example Display the configurations of all Ethernet ports and port channels: T2600G-28TS(config)# show interface configuration Display the configurations of port 1/0/2: T2600G-28TS(config)# show interface configuration gigabitEthernet 1/0/2 83 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 107
port isolation Description The port isolation command is used to configure the forward port/port channel list of a port/port users have access to these commands. Example Set port 1, 2, 4 and port channel 2 to the forward list of port 1/0/5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 108
its forward port list, ranging from 1 to 6. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the forward-list of port 1/0/2: T2600G-28TS# show port isolation interface gigabitEthernet 1/0/2 Display the forward-list of all Ethernet ports and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 109
, the switch will display an alert or further block the corresponding port according to the configuration. 11.1 Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the loopback detection function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 110
to 1000000 seconds. By default, this value is 90. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the recovery-time as 70 seconds: T2600G-28TS(config)# loopback-detection recovery-time 70 87 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 111
config)# interface range gigabitEthernet 1/0/1-3 T2600G-28TS(Config-if-range)# loopback-detection 11.5 loopback-detection config process-mode Description The loopback-detection config process-mode command is used to configure the process-mode for the ports by which the switch copes with the detected - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 112
Only Admin, Operator and Power User level users have access to these commands. Example Configure the loopback detection process-mode as port-based, and configure the recovery mode as manual for port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# loopback-detection - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 113
. Syntax show loopback-detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of loopback detection function: T2600G-28TS# show loopback-detection global 11.8 show loopback-detection interface Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 114
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of loopback detection function and the status of all ports: T2600G-28TS# show loopback-detection interface Display the configuration of loopback detection function and the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 115
for Certain Devices) Note: Only T2600G-18TS, T2600G-28TS, T2600G-28MPS V4, and T2600G-28SQ support DDM function. The DDM (Digital Diagnostic Monitoring) function allows the user to monitor the status of the SFP modules inserted into the SFP ports on the switch. The user can choose to shut down the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 116
when an exceeding warning threshold event is encountered: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm shutdown warning 12.3 ddm temperature_threshold Description The ddm temperature_threshold command is used to configure the threshold of the DDM temperature value - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 117
of DDM temperature on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm temperature_threshold high_alarm 5 12.4 ddm voltage_threshold Description The ddm voltage_threshold command is used to configure the threshold of the DDM voltage value. Syntax - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 118
of DDM voltage on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm voltage_threshold high_alarm 5 12.5 ddm bias_current_threshold Description The ddm bias_current_threshold command is used to configure the threshold of the DDM Bias Current value - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 119
of DDM Bias Current on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm bias_current_threshold high_alarm 5 12.6 ddm tx_power_threshold Description The ddm tx_power_threshold command is used to configure the threshold of the DDM Tx Power value - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 120
of DDM Tx Power on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm tx_power_threshold high_alarm 5 12.7 ddm rx_power_threshold Description The ddm rx_power_threshold command is used to configure the threshold of the DDM Rx Power value. Syntax ddm - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 121
port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm rx_power_threshold high_alarm 5 12.8 show ddm configuration Description The show ddm configuration command is used to display the DDM configuration. Syntax show ddm configuration { state | temperature - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 122
command is used to display the DDM status, which is the digital diagnostic monitoring status of SFP modules inserting into the switch's SFP ports. Syntax show ddm status Command Mode Privileged EXEC Mode and Any Configuration Mode Example View the DDM status: T2600G-28TS(config)#show ddm status 99 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 123
Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 124
Group 1 and enable the static LAG: T2600G-28TS(config)# interface range gigabitEthernet 1/0/2-4 T2600G-28TS(config-if-range)# channel-group 1 mode on 13.2 port-channel load-balance Description The port-channel load-balance command is used to configure the Aggregate Arithmetic for LAG. To return - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 125
ranging from 0 to 65535. It is 32768 by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the LACP system priority as 1024 globally: T2600G-28TS(config)# lacp system-priority 1024 102 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 126
gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the LACP port priority as 1024 for ports 1-3: T2600G-28TS(config)# interface range gigabitEthernet 1/0/1-3 T2600G-28TS(config-if-range)# lacp port-priority 1024 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 127
-- The EtherChannel information in summary. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the detailed information of EtherChannel Group 1: T2600G-28TS(config)# show etherchannel 1 detail 13.6 show etherchannel load-balance Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 128
information. neighbor -- The neighbor LACP information. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the internal LACP information of EtherChannel Group 1: T2600G-28TS(config)# show lacp 1 internal 13.8 show lacp sys-id Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 129
Example Display the LACP system priority: T2600G-28TS(config)# show lacp sys-id 106 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 130
manually, independent of the aging time. In the stable networks, the static MAC address entries can facilitate the switch of your desired entry. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 131
port on which you desire to delete MAC addresses. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Delete the MAC addresses on VLAN 1: T2600G-28TS(config)# no mac address-table dynamic vid 1 14.3 mac - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 132
and Power User level users have access to these commands. Example Configure the aging time as 500 seconds: T2600G-28TS(config)# undesired package to be forwarded. The filtering address can be added or removed manually, independent of the aging time. Syntax mac address-table filtering mac-addr - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 133
of the switch's MAC Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the global MAC address notification and table full notification, specify the notification sending interval as 2 seconds: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 134
is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted. When permanent mode is selected, the learned MAC address will be out of the influence of the aging time - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 135
-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# mac address-table max-mac-count max-number 30 mode static status drop 14.7 mac address-table notification (interface) Description The mac address-table notification command is used to configure the MAC change notification on port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 136
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the learn-mode-change notification on port 1/0/2: T2600G-28TS(config)# mac - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 137
address-table vlan-security (For T2600G-18TS) Description The mac address-table security command is used to configure the maximum number of MAC Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 138
T2600G-18TS(config)# mac address-table vlan-security vid 2 max-learn 1000 14.10 are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all address entries: T2600G-28TS(config)# show mac address-table 14.11 clear - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 139
and Power User level users have access to these commands. Example Clear the information of all static address entries: T2600G-28TS(config Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the Aging Time of the MAC address: T2600G-28TS(config)# show mac - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 140
-28TS(config)# show mac address-table max-mac-count all Display the security configuration of port 1/0/1: T2600G-28TS(config)# show mac address-table max-mac-count interface gigabitEthernet 1/0/1 14.14 show mac address-table interface Description The show mac address-table interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 141
the VLAN which the MAC entries belong to. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the total MAC entry information in different VLANs: T2600G-28TS(config)# show mac address-table count 14.16 show mac address-table address Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 142
vlan vid Parameter vid --The specified VLAN id. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MAC address configuration of vlan 1: T2600G-28TS(config)# show mac address-table vlan 1 14.18 show mac address-table notification Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 143
the notification information on the specified port. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the notification configuration of all the ports: T2600G-28TS(config)# show mac address-table notification all 14.19 show mac address-table - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 144
Network) technology is developed for the switch to divide the LAN into multiple Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN 2-10 and VLAN 100: T2600G-28TS(config)# vlan 2-10,100 Delete VLAN 2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 145
16 characters at most. Command Mode VLAN Configuration Mode(VLAN) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the name of VLAN 2 as "group1": T2600G-28TS(config)# vlan 2 T2600G-28TS(config-vlan)# name group1 15.3 vlan_trunk - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 146
is disabled. Syntax vlan_trunk no vlan_trunk Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / User level users have access to these commands. Example Enable VLAN Trunk for port 1/0/3: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 147
Only Admin, Operator and Power User level users have access to these commands. Example Configure Gigabit Ethernet port 1/0/4 whose link type is "general" to VLAN 2 and its egress-rule as "tagged": T2600G-28TS(config)#interface gigabitEthernet 1/0/4 T2600G-28TS(config-if)#switchport general allowed - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 148
User level users have access to these commands. Example Specify the PVID of port 1/0/2 as 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G- check ingress no switchport check ingress Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 149
type for the switch ports and the ports Command Mode Interface Configuration Mode (interface gigabitEthernet User level users have access to these commands. Example Specify the acceptable frame type of Gigabit Ethernet port 1/0/4 as "tagged": T2600G-28TS(config)#interface gigabitEthernet 1/0/4 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 150
information of IEEE 802.1Q VLAN. Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the brief information of IEEE 802.1Q VLAN: T2600G-28TS(config)# show vlan brief 15.11 show vlan Description The show vlan command is used - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 151
port -- The port number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the VLAN configuration information of all ports and port channels: T2600G-28TS(config)# show interface switchport 128 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 152
-- Give a Description to the MAC address for identification, which contains 8 characters at most. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN 2 with the MAC address 00:11:11:01:01:12 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 153
T2600G-28TS(config)#mac-vlan mac-address 00:11:11:01:01:12 vlan 2 Description TP 16.2 mac-vlan Description The mac-vlan command is used to enable a port for the MAC-based VLAN feature. Only the port is enabled can the configured MAC-based VLAN take effect. To disable the MAC-based VLAN - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 154
interface command is used to display the port state of MAC-based VLAN. Syntax show mac-vlan interface Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the enable state of all the ports: T2600G-28TS(config)#show mac-vlan interface 131 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 155
of the Protocol-based VLAN Template. You can get the template corresponding to the number by the show protocol-vlan template command. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. 132 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 156
TP" whose Ethernet protocol type is 0x2024: T2600G-28TS(config)#protocol-vlan template name TP VLAN, ranging from 0-7. The switch will determine the forwarding sequence according Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 157
Specify the protocol group ID. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / User level users have access to these commands. Example Add Gigabit Ethernet port 20 to protocol group 1: T2600G-28TS(config)#interface gigabitEthernet 1/0/20 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 158
Syntax show protocol-vlan template Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of the Protocol-based VLAN templates: T2600G-28TS(config)#show protocol-vlan template 17.5 show protocol-vlan vlan Description The show protocol - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 159
. Private VLAN Commands Note: T2600G-18TS does not support Private VLAN. Private VLANs are configured specially for saving VLAN resource of uplink devices and decreasing broadcast. 18.1 private-vlan primary Description The private-vlan primary command is used to configure the designated VLAN as the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 160
Mode (VLAN) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the VLAN 4 as the community VLAN of the private VLAN: T2600G-28TS(config)#vlan 4 T2600G-28TS(config-vlan)#private-vlan community 18.3 private-vlan isolated Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 161
from 2 to 4094. Command Mode VLAN Configuration Mode (VLAN) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Associate primary VLAN 3 with community VLAN 4 as a private VLAN: T2600G-28TS(config)#vlan 3 T2600G-28TS(config-vlan)#private-vlan association - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 162
interface range port-channel) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure Gigabit Ethernet port 3 as "host": T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport private-vlan host 18.6 switchport private - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 163
Requirement Only Admin and Operator level users have access to these commands. Example Configure promiscuous type Gigabit Ethernet port 1/0/3 as a member of primary VLAN 3 and secondary VLAN 4: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport private-vlan - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 164
information of the switch. Syntax show vlan private-vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display the configuration information of all Private VLAN: T2600G-28TS(config)#show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 165
Example Display the configuration information of all the Ethernet ports: T2600G-28TS(config)#show vlan private-vlan interface 142 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 166
networks at the network access terminal of the Internet Service Provider. And these packets will be transmitted with double Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the VLAN-VPN function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 167
range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure TPID of port 1/0/2 as 0x9100: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#switchport dot1q-tunnel tpid 9100 19.3 dot1q-tunnel - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 168
port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the Gigabit Ethernet port 1/0/3 as the VPN UNI ports: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport dot1q-tunnel mode uni 145 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 169
-tunnel missdrop Note: For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS, Missdrop can only be enabled on UNI ports. For T2600G-18TS, Missdrop can only be no switchport dot1q-tunnel missdrop Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 170
(config-if)#switchport dot1q-tunnel use_inner_priority 19.7 switchport dot1q-tunnel mapping Note: For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS, choose a UNI port to enable VLAN mapping. For T2600G-18TS, choose a NNI port to enable VLAN mapping. Description The switchport dot1q-tunnel mapping - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 171
Interface Configuration Mode Service Provider VLAN as VLAN 3: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport dot1q-tunnel mapping 2 3 19.8 switchport dot1q-tunnel replace Note: Only T2600G-28TS, T2600G-28TS-DC, T2600G-28MPS, T2600G-28SQ, and T2600G-52TS support - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 172
and Power User level users have access to these commands. User Guidelines Before configuring VLAN Replace, enable VLAN Mapping globally. Example Add a VLAN Replace entry on the Gigabit Ethernet port 1/0/3 to replace the Customer VLAN (VLAN 2) with the Service Provider VLAN (VLAN 3): T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 173
of VLAN Mapping entry. Syntax show dot1q-tunnel mapping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of VLAN Mapping entry: T2600G-28TS(config)#show dot1q-tunnel mapping 19.11 show dot1q-tunnel interface Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 174
local VLAN registration information to other switches, without having to individually configure each VLAN. 20.1 gvrp Description Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the GVRP function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 175
User level users have access to these commands. Example Enable the GVRP function for Gigabit Ethernet ports 1/0/2-6: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6 T2600G-28TS(config-if-range)#gvrp 20.3 gvrp registration Description The gvrp registration command is used to configure - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 176
Example Configure the GVRP registration mode as "fixed" for Gigabit Ethernet ports 1/0/2-6: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6 T2600G-28TS(config-if-range)#gvrp registration fixed 20.4 gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 177
. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the GVRP configuration information of Gigabit Ethernet port 1: T2600G-28TS(config)#show gvrp interface gigabitEthernet 1/0/1 Display the GVRP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 178
20.6 show gvrp global Description The show gvrp global command is used to display the global GVRP status. Syntax show gvrp global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global GVRP status: T2600G-28TS(config)#show gvrp global 155 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 179
command. Syntax ip igmp snooping no ip igmp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IGMP Snooping function: T2600G-28TS(config)# ip igmp snooping 21.2 ip igmp snooping version - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 180
as an IGMPv3 Snooping switch. It can process IGMPv1, IGMPv2 and IGMPv3 messages from the host. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the IGMP version as v2: T2600G-28TS (config)# ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 181
-validation no ip igmp snooping header-validation Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IGMP Header Validation: T2600G-28TS(config)# ip igmp snooping header-validation 21.5 ip igmp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 182
switch Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Snooping function and modify Router Port Aging Time as 300 seconds, Member Port Aging Time as 200 seconds for VLAN 1-3: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 183
from 1 to 4094, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Fast Leave for VLAN 1-3: T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 immediate-leave 21 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 184
4094, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Report Suppression for VLAN 1-3: T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 report-suppression - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 185
be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1 : T2600G- - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 186
Power User level users have access to these commands. Example Set the router port as 1/0/1 for VLAN 1-2: T2600G-28TS(config)# ip igmp snooping vlan-config 1-2 rport interface gigabitEthernet 1/0/1 21.10 ip igmp snooping vlan-config (static) Description This command is used to configure interfaces - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 187
T2600G- Parameter vlan-id-list -- The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5. response-time ip-addr-- The source IP address of the general query messages sent by the switch. It should be a unicast address. By default, it is 0.0.0.0. count - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 188
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Snooping Querier for VLAN 3, and configure the query interval as 100 seconds: T2600G-28TS(config)# ip igmp snooping vlan-config 3 querier T2600G-28TS(config)# ip igmp snooping vlan - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 189
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the maximum numbers of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5 166 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 190
-28TS(config-if-range)#ip igmp snooping max-groups 10 T2600G-28TS(config-if-range)#ip igmp snooping max-groups action replace 21.14 ip igmp snooping immediate-leave Description The ip igmp snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the Fast - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 191
Syntax ip igmp snooping accounting no ip igmp snooping accounting Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IGMP accounting globally: T2600G-28TS(config)# ip igmp snooping accounting 168 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 192
Parameter id -- Specify the id of the configuration profile, ranging from 1 to 999. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the profile 1: T2600G-28TS(config)# ip igmp profile 1 21.18 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 193
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the filtering mode of profile 1 as permit: T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#permit 21.20 range Description The range command - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 194
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure one of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1: T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#range 225.1.1.1 226 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 195
ip igmp snooping statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear the statistics of the IGMP packets: T2600G-28TS(config)# clear ip igmp snooping statistics 21.23 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 196
information selected to display. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IGMP baisic configuration configuration of all ports and port channels: T2600G-28TS# show ip igmp snooping interface basic-config Display the IGMP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 197
vlan-id --The VLAN ID selected to display. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IGMP snooping configuration information of VLAN 2: T2600G-28TS# show ip igmp snooping vlan 2 21.26 show ip igmp snooping groups Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 198
groups. static count-- The numbers of all static multicast groups. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all IGMP snooping groups: T2600G-28TS#show ip igmp snooping groups Display all the multicast entries in VLAN - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 199
Parameter id -- Specify the ID of the profile, ranging from 1 to 999. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of all profiles: T2600G-28TS(config)# show ip igmp profile 176 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 200
Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable MLD Snooping: T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 201
and Operator level users have access to these commands. Example Enable unknown multicast filter function: T2600G-28TS(config)# ipv6 desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5. router-time -- The Router Port Aging Time. Within this time, if the switch does not - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 202
200 seconds for VLAN 1-3: T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-3 rtime 300 T2600G-28TS(config)# ipv6 mld configuration, ranging from 1 to 4094, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 203
4094, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the MLD Report Suppression for VLAN 1-3: T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-3 report-suppression - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 204
be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1: T2600G- - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 205
-list-- The ID of the port channels. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Set the router port as 1/0/1 for VLAN 1-2: T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-2 rport interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 206
the port channels. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure port ports 1/0/1-3 in VLAN 2 to statically join multicast group ff80::1234:1: T2600G-28TS(config)# ipv6 mld snooping vlan - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 207
query-interval interval-- The interval between general query messages sent by the switch. Valid values are from 10 to 300 seconds, and the default value second. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 208
level users have access to these commands. Example Enable MLD Snooping on port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ipv6 mld snooping 22.11 ipv6 mld snooping max-groups Description The ipv6 mld snooping max-groups command is used to configure the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 209
Only Admin and Operator level users have access to these commands. Example Specify the maximum numbers of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5 T2600G-28TS(config-if-range)#ipv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 210
mld profile id Parameter id -- Specify the id of the configuration profile, ranging from 1 to 999. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Create the profile 1: T2600G-28TS(config)# ipv6 mld profile 1 187 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 211
as deny. Syntax deny Command Mode Profile Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the filtering mode of profile 1 as deny: T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-MLD-profile)#deny 22.15 permit - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 212
Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure one of the filter multicast address entry as range ff80::1234 to ff80::1235 in profile 1: T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-igmp-profile)#range ff80::1234 ff80 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 213
mld snooping statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear the statistics of the MLD packets: T2600G-28TS(config)# clear ipv6 mld snooping statistics 22.19 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 214
information selected to display. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MLD baisic configuration configuration of all ports and port channels: T2600G-28TS# show ipv6 mld snooping interface basic-config Display the MLD - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 215
-- The VLAN ID selected to display, ranging from 1 to 4094. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display all of the VLAN information: T2600G-28TS(config)# show ipv6 mld snooping vlan 22.22 show ipv6 mld snooping groups Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 216
. static count-- The numbers of all static multicast groups. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display all of the multicast groups: T2600G-28TS(config)# show ipv6 mld snooping groups 22.23 show ipv6 mld profile Description The show ipv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 217
MVR, please use no mvr command. Syntax mvr no mvr Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable MVR globally: T2600G-28TS(config)# mvr 23.2 mvr group Description The mvr group command is used - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 218
256, and the default value is 1. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add multicast groups 225.1.2.3 -239.1.2.5 to MVR: T2600G-28TS (config)# mvr group 225.1.2.3 3 23.3 mvr mode Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 219
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the MVR mode as dynamic: T2600G-28TS(config)# mvr mode dynamic 23.4 mvr querytime Description The mvr querytime command is used to configure the maximum time to wait for IGMP report - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 220
VLAN. Valid values are from 1 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the multicast VLAN as VLAN 10: T2600G-28TS(config)# mvr vlan 10 23.6 mvr (interface) Description This - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 221
/ interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the port 1/0/3 as a receiver port: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#mvr type receiver 198 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 222
no mvr immediate Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. User Guidelines Only receiver ports support Fast Leave. Before enabling Fast - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 223
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. User Guidelines This command applies to only receiver ports. The switch adds or removes the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 224
number. port-list -- The list of Ethernet ports. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MVR configuration of port 1/0/3: T2600G-28TS# show mvr interface gigabitEthernet 1/0/3 23.12 show mvr members Description The show mvr members - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 225
Example Display the membership information of all MVR groups: T2600G-28TS# show mvr members 202 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 226
Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths. 24.1 debug spanning-tree Description The debug spanning-tree command is used to enable debuggning of spanning-tree - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 227
command. Syntax spanning-tree no spanning-tree Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the STP function: T2600G-28TS(config)# spanning-tree 24.3 spanning-tree (interface) Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 228
Power User level users have access to these commands. Example Enable the STP function for port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# spanning-tree 24.4 spanning-tree common-config Description The spanning-tree common-config command is used to configure - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 229
-- The P2P link status, with auto, open and close options. T2600G-28TS(config-if)# spanning-tree common-config port-priority 64 ext-cost 100 int-cost 100 portfast enable point-to-point open 24.5 spanning-tree mode Description The spanning-tree mode command is used to configure the STP mode of the switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 230
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enter into the MST configuration mode: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(Config-mst)# 24.7 instance Description The instance command is used to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 231
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Map the VLANs 1-100 to Instance 1: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(config-mst)# instance 1 vlan 1-100 Disable Instance 1, namely remove all the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 232
from 0 to 65535. Command Mode MST Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the revision level of MST as 100: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(config-mst)# revision 100 209 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 233
if the switch will be chosen as the root bridge in the specific instance. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the MST Instance 1 and configure its priority as 4096: T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 234
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the priority of port 1 in MST Instance 1 as 64, and path cost as 2000: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# spanning-tree mst instance - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 235
User level users have access to these commands. Example Configure the bridge priority as 4096: T2600G-28TS(config)# spanning-tree priority 4096 24.13 spanning-tree timer Description The spanning-tree timer command is used to configure packets, and used to test the links. Hello Time ranges from 1 to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 236
to 20 in pps. By default, it is 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the hold-count of STP as 8pps: T2600G-28TS(config)# spanning-tree hold-count 8 24.15 spanning-tree max-hops - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 237
1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max-hops of STP as 30: T2600G-28TS(config)# spanning-tree max-hops 30 24.16 spanning-tree bpdufilter - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 238
no spanning-tree bpduflood Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet User level users have access to these commands. Example Enable the BPDU forward function for port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 239
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Loop Protect function for port 2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 240
receiving TC-BPDUs. If a malicious user continuously sends TC-BPDUs to a switch, the switch will be busy with removing MAC address entries, which may decrease the performance and stability of the network. With the Protect of Spanning Tree function enabled, you can configure the number of TC-BPDUs in - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 241
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable mcheck for port 2: T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 242
hold-count | max-age | max-hops | mode | priority | state ] Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bridge parameters: T2600G-28TS(config)# show spanning-tree bridge 24.25 show spanning-tree interface Description The show spanning - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 243
number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the spanning-tree information of all ports: T2600G-28TS(config)# show spanning-tree interface Display the spanning-tree information of port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 244
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the protect information of all ports: T2600G-28TS(config)# show spanning-tree interface-security Display the protect information of port 1: T2600G-28TS(config)# show spanning-tree interface- - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 245
Display the related information of MST Instance 1: T2600G-28TS(config)#show spanning-tree mst instance 1 Display all the ports information of MST Instance 1: T2600G-28TS(config)#show spanning-tree mst instance 1 interface 222 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 246
lldp command. Syntax lldp no lldp Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable LLDP function globally: T2600G-28TS(config)#lldp 25.2 lldp forward_message Description The lldp forward_message - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 247
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the switch to forward LLDP messages when LLDP function is disabled globally: T2600G-28TS(config)#lldp forward_message 25.3 lldp hold-multiplier - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 248
equals this parameter). The value ranges from 1 to 10 and the default value is 3. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the Transmit Interval of LLDPDU as 45 seconds and Trap message - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 249
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable port 1/0/1 to receive LLDPDU: T2600G-28TS(config)#interface gigabitEthernet - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 250
. Syntax lldp snmp-trap no lldp snmp-trap Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the SNMP notification for Gigabit - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 251
protocol-vlan ] [ vlan-name ] [ link-aggregation ] [ mac-phy-cfg ] [ max-frame-size ] [ power ] [ all ] } Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 252
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the port's management address as 192.168.1.100 for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# lldp management-address 192.168 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 253
and Power User level users have access to these commands. Example Enable the LLDP-MED feature for port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# lldp med-status 25.12 lldp med-tlv-select Description The lldp med-tlv-select command is used to configure LLDP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 254
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Exclude "network policy" and "inventory" TLVs in LLDPDU outgoing from port 1/0/2: T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 255
and Power User level users have access to these commands. Example Configure the civic address in the Location Identification TLV's content in outgoing LLDPDU of port 1/0/2. Configure the language as English and city as London: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 256
port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the LLDP configuration of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp interface gigabitEthernet 1/0/1 25.16 show lldp local-information interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 257
port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the neighbor information of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp neighbor-information interface gigabitEthernet 1/0/1 25.18 show lldp traffic - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 258
Privilege Requirement None. Example Display the LLDP statistic information of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp traffic interface gigabitEthernet 1/0/1 235 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 259
. L2PT Commands L2PT (Layer 2 Protocol Tunneling) is a feature for service providers to transmit packets from different customers across their ISP networks and maintain Layer 2 protocol configurations of each customer. The supported Layer 2 protocols are STP (Spanning Tree Protocol), GVRP (GARP VLAN - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 260
is connecting to the user's local network. 01000ccccccc | 01000ccccccd | gvrp | stp | lacp | all -- Select the supported Layer 2 protocol type ■ all: All the above Layer 2 protocols are supported for tunneling. ■ threshold --Configure the threshold for packets-per-second accepted for encapsulation. - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 261
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure port 1/0/3 as a UNI port for STP packets with the threshold as 1000 packets/second: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# l2protocol-tunnel type uni stp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 262
-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the L2PT configuration information of Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#show l2protocol-tunnel interface gigabitEthernet 1/0/1 Display the L2PT - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 263
(authentication, authorization, and accounting) access requests. The switch will remove the Circuit-ID/Remote-ID tag from the Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the PPPoE ID-Insertion function: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 264
. Syntax pppoe circuit-id no pppoe circuit-id Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the PPPoE Circuit-ID Insertion - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 265
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the type of PPPoE Circuit-ID as "mac" for the Gigabit Ethernet port 1/0/1: T2600G-28TS (config)# interface gigabitEthernet 1/0/1 T2600G-28TS (config-if)# pppoe circuit-id type - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 266
gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the remote-ID as "mac" for the Gigabit Ethernet port 1/0/1: T2600G-28TS (config)# interface gigabitEthernet 1/0/1 T2600G-28TS (config-if)# pppoe remote-id mac 27 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 267
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of PPPoE Circuit-ID Insertion function of all Ethernet ports: T2600G-28TS# show pppoe id-insertion interface Display the configuration of PPPoE Circuit-ID Insertion function - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 268
. Syntax ip routing no ip routing Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IPv4 routing feature for the switch: T2600G-28TS(config)# ip routing 28.2 interface vlan Description This - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 269
Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the loopback interface 1: T2600G-28TS(config)# interface loopback 1 28.4 switchport Description This switchport command is used to switch the Layer - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 270
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Switch port 1/0/9 into the routed port: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 271
32 characters. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a Description system-if to the routed port 1/0/9 : T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 272
Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Shut down the routed port 1/0/9: T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 273
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a static route with the destination IP address as 192.168.2.0, the subnet mask as 255.255.255.0 and the next-hop address as 192.168.0.2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 274
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IPv6 routing globally: T2600G-28TS(config)# ipv6 routing 28.11 ipv6 route Description This ipv6 route command is configure the IPv6 static route. To clear the corresponding - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 275
show interface vlan vid Parameter vid -- The VLAN ID. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of VLAN 2: T2600G-28TS(config)#show interface vlan 2 28.13 show ip interface Description This show ip interface command is - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 276
the Layer 3 interfaces. Syntax show ip interface brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the summary information of the Layer 3 interfaces: T2600G-28TS(config)# show ip interface brief 28.15 show ip route Description This show ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 277
match the network segment determined by the ip and mask parameters. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the shortest route to 192.168.0.100: T2600G-28TS(config)# show ip route specify 192.168.0.100 Look up the route entry with the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 278
Display the summary information of route entries: T2600G-28TS(config)# show ip route summary 28.18 show ipv6 interface Description This command is used to display the configured IPv6 information of the management interface, including ipv6 function status, link-local address and global address, IPv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 279
displayed. static: The static routes. connected: The connected routes. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IPv6 static routes: T2600G-28TS(config)# show ipv6 route static 28.20 show ipv6 route summary Description This show ipv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 280
Privilege Requirement None. Example Display the summary information of IPv6 route entries: T2600G-28TS(config)# show ipv6 route summary 257 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 281
no ipv6 enable Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IPv6 function on the VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 enable 258 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 282
address autoconfig Description This command is used to enable the automatic configuration of the ipv6 link-local address. The switch has only one ipv6 link-local address, which can be configured automatically or manually. The general ipv6 link-local address has the prefix as fe80::/10. IPv6 routers - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 283
Only Admin, Operator and Power User level users have access to these commands. Example Configure the link-local address as fe80::1234 on the VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address fe80::1234 link-local 29.4 ipv6 address dhcp Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 284
to obtain IPv6 address through the RA message on VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address ra 29.6 ipv6 address eui-64 Description This command is used to manually configure a global IPv6 address with an extended unique identifier (EUI) in the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 285
users have access to these commands. Example Configure an EUI-64 global address on the interface with the network prefix 3ffe::/64: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address 3ffe::/64 eui-64 29.7 ipv6 address Description This command is used to manually configure - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 286
on VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address 3001::1/64 29.8 show ipv6 interface Description This command is used to display the configured ipv6 information of the management interface, including ipv6 function status, link-local address and global - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 287
. The switch maintains an ARP entry is manually configured and maintained. 30 Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a static ARP entry with the IP as 192.168.0.1 and the MAC as 00:11:22:33:44:55: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 288
, Operator and Power User level users have access to these commands. Example Clear all the dynamic ARP entries: T2600G-28TS(config)# clear arp Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the switch to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 289
The default value is 600 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the ARP aging time as 60 seconds on interface 1/0/1: T2600G-28TS(config-if)# arp timeout 60 30.5 gratuitous - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 290
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Enable the switch's Layer 3 interfaces to send gratuitous ARP packets when their status becomes up: T2600G-28TS(config)# gratuitous-arp intf-status-up enable 30.6 gratuitous-arp dup-ip-detected enable - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 291
gratuitous-arp learning enable Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Enable the Layer 3 interface to learn MAC addresses from the gratuitous ARP packets: T2600G-28TS(config)# gratuitous-arp learning enable 30.8 gratuitous-arp send-interval - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 292
proxy-arp no ip proxy-arp Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ARP function on routed port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 2 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if)# ip proxy-arp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 293
arp no ip local-proxy-arp Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / Proxy ARP function on routed port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 2 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if)# ip local-proxy-arp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 294
the port channel. id -- Specify the VLAN interface ID. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the ARP entry associated with VLAN interface 2: T2600G-28TS(config)# show ip arp vlan 2 30.13 show ip arp summary Description This show ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 295
of gratuitous ARP. Syntax show gratuitous-arp Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of gratuitous ARP: T2600G-28TS(config)# show gratuitous-arp 30.15 show ip proxy-arp Description The show ip proxy-arp command - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 296
Privilege Requirement None Example Display the Proxy ARP status: T2600G-28TS(config)# show ip proxy-arp 273 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 297
server command. Syntax service dhcp server no service dhcp server Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable DHCP server service globally: T2600G-28TS(config)# service dhcp server 31.2 ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 298
of an AC (Access Control) device. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Set the remote DHCP server's IP address as 192.168.3.1: T2600G-28TS(config)# ip dhcp server extend-option capwap-ac-ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 299
the DHCP packets from another network segment as 34: T2600G-28TS(config)# ip dhcp server extend-option vendor-class IP address are the same. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Set the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 300
address pool name, ranging from 1 to 8 characters. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the address pool of name POOL1: T2600G-28TS(config)# ip dhcp server pool POOL1 31.6 ip dhcp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 301
packets' number, ranging from 0 to 10. By default it's 1. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the PING packets' number as 2: T2600G-28TS(config)# ip dhcp server ping packets 2 278 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 302
Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool "product" as 192.168.1.0 255.255.255.0: T2600G-28TS(config)# ip dhcp server pool product T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 303
Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the lease time of address pool "product" as 10 minutes: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# lease 10 31.10 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 304
in the format of hex value. ascii -- The client ID is entered with ASCII characters. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Reserve the IP address 192.168.0.10 in the address pool "product" for - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 305
, separated by comma. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool product's default gateways as 192.168.0.1 and 192.168.1.1: T2600G-28TS(config)# ip dhcp server pool product - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 306
, separated by comma. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool's Netbios servers as 192.168.0.1 and 192.168.1.1: T2600G-28TS(config)# ip dhcp server pool product - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 307
User level users have access to these commands. Example Specify the address pool's Netbios server type as b-node: T2600G-28TS(config)# ip dhcp server pool product T2600G . Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 308
the DHCP client. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the DHCP client's domain name as edu: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# domain-name edu - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 309
status command is used to display the status of the DHCP service. Syntax show ip dhcp server status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the status of DHCP service: T2600G-28TS(config)# show ip dhcp server status 31.20 show ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 310
servers. Syntax show ip dhcp server extend-option Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configurations of the remote DCHP servers: T2600G-28TS(config)# show ip dhcp server extend-option 31.22 show ip dhcp server pool Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 311
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configured reserved addresses: T2600G-28TS(config)# show ip dhcp server excluded-address 31.24 show ip dhcp server manual-binding Description The show ip dhcp server manual-binding command is used to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 312
Privilege Requirement None. Example Display the configured static binding address: T2600G-28TS(config)# show ip dhcp server manual-binding 31.25 show ip dhcp server binding Description The show ip dhcp server binding command is used to display the binding entries. Syntax show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 313
-address -- Specify the binding IP address. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear all the binding addresses: T2600G-28TS(config)# clear ip dhcp server binding 290 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 314
dhcp relay command. Syntax service dhcp relay no service dhcp relay Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable DHCP Relay function globally: T2600G-28TS(config)# service dhcp relay 32.2 ip - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 315
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of relay hops as 6: T2600G will be dropped by the switch. To restore the default value, please use no service dhcp relay time command. Syntax - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 316
DHCP Server address. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add DHCP Server address 192.168.2.1 to interface VLAN 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ip helper - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 317
User level users have access to these commands. Example Enable option 82 support in DHCP Relay for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G with the system option defined by the switch. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 318
packet for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 319
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the circuit ID as "TP-Link" for port 2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 320
-Link" for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp relay information remote-id TP-Link 32.10 ip dhcp relay default-interface Description The ip dhcp relay default-interface command is used to configure default relay agent interface. When the switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 321
ID. ip-address -- DHCP Server address. Command mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add DHCP server address 192.168.2.1 to VLAN 1: T2600G-28TS(config)# ip dhcp relay vlan 1 helper-address 192.168 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 322
Privilege Requirement None. Example Display the configuration of DHCP Relay: T2600G-28TS(config)# show ip dhcp relay 299 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 323
. Syntax ip dhcp l2relay no ip dhcp l2relay Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable DHCP L2 Relay function globally: T2600G-28TS(config)# ip dhcp l2relay 33.2 ip dhcp l2relay vlan - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 324
range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable option 82 support in DHCP Relay for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp l2relay information 33.4 ip dhcp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 325
82 field in the packet. replace: Replace the option 82 field with the system option defined by the switch. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 326
the related sub-option. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Select - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 327
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the remote ID as "TP-Link" for port 2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 328
interface [ gigabitEthernet port | port-channel port-channel-id ] Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCP L2 Relay configuration of port 1/0/2: T2600G-28TS(config)# show ip dhcp l2relay interface gigabitEthernet 1/0/2 305 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 329
. It provides you with network service experience of a better quality. The switch implements three priority modes based on port, on 802.1p and on DSCP. 34.1 qos trust mode Description The qos trust mode command is used to configure the trust mode of CoS (Class of Service) function for the ports. The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 330
/ interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the priority of port 5 as 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# qos port-priority 3 34.3 qos cos-map - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 331
will be mapped to. It ranges from 0 to 7. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Map the 802.1p priority 5 to TC-2: T2600G-28TS (config)# qos cos-map 5 2 34.4 qos dot1p-remap Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 332
gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) For T2600G-18TS: Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Remap 802.1p priority 5 to 802.1p - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 333
For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) For T260G-18TS: Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 334
-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The qos queue bandwidth command is used to configure the minimum guaranteed bandwidth allocated to the specified queue. A value of 0 means there is no guaranteed minimum bandwidth in effect (best-effort service). The default value is 0. The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 335
T2600G-28TS(config-if)# qos queue 5 bandwidth 10 34.8 qos queue mode Description The qos queue mode command is used to configure the Scheduler Mode. When the network is congested, the program that many packets complete for resources must be solved, usually in the way of queue scheduling. The switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 336
-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the 802.1p to queue mappings: T2600G-28TS# show qos cos-map 34.10 show qos dot1p-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dot1p-remap - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 337
Mode Privilege Requirement None. Example Display the IEEE 802.1P remap configuration: T2600G-18TS# show qos dot1p-remap 34.12 show qos dscp-map interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dscp-map interface command is used to display the DSCP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 338
-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DSCP priority configuration: T2600G-18TS# show qos dscp-map 34.14 show qos dscp-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dscp-remap - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 339
priority to DSCP priority mappings. Syntax show qos dscp-remap Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DSCP to DSCP mappings: T2600G-18TS# show qos dscp-remap 34.16 show qos port-priority interface Description The show qos port - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 340
. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the trust mode of all the ports: T2600G-28TS# show qos trust interface 34.18 show qos queue interface Description The show qos queue interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 341
-channel port-channel-id ] Parameter port -- The port number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the scheduler settings of all the ports: T2600G-28TS# show qos queue interface 318 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 342
of the interface. To return to the default configuration, please use no storm-control rate-mode command. Syntax For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: storm-control rate-mode { kbps | ratio | pps } no storm-control rate-mode For T2600G-18TS storm-control rate-mode { kbps | ratio } no - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 343
range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. User Guidelines Before you configure the storm-control type as kbps or ratio, pelease ensure that the port is not in pps - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 344
you can recover the port manually using storm-control recover command. Command Mode Interface Configuration Mode (interface gigabitEthernet / User level users have access to these commands. Example Configure the action as drop on port 1/0/5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 345
, Operator and Power User level users have access to these commands. Example Recover port 1/0/5 manually: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# storm-control recover 35.5 bandwidth Description The bandwidth command is used to configure the bandwidth limit for - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 346
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the ingress-rate as 5120Kbps and egress-rate as 1024Kbps for port 1/0/5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# bandwidth ingress 5120 egress - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 347
list of Ethernet ports. port-channel-id-list -- The list of port channels. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bandwidth-limit information of port 1/0/4: T2600G-28TS(config)# show bandwidth interface gigabitEthernet 1/0/4 324 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 348
VLAN ID, ranging from 2 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Voice VLAN function for VLAN 10: T2600G-28TS(config)# voice vlan 10 36.2 voice vlan (interface) Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 349
and Power User level users have access to these commands. Example Enable the Voice VLAN function for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#voice vlan 36.3 voice vlan priority Description The voice vlan priority command is used to configure the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 350
OUI for identification which contains 16 characters at most. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a Voice VLAN OUI described as TP-Phone with the OUI address 00:11:11:11:11:11 and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 351
voice vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the configuration information of Voice VLAN globally: T2600G-28TS(config)# show voice vlan 36.6 show voice vlan - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 352
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the Voice VLAN configuration information of all ports and port channels: T2600G-28TS(config)# show voice vlan interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 353
disable the Auto VoIP function, use no auto-voip command. Syntax auto-voip no auto-voip Command Mode Global Configuration Mode Example Enable the Auto VoIP function globally: T2600G-28TS(config)# auto-voip 37.2 auto-voip (interface) Description The auto-voip command is used to specify the interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 354
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Example Set Auto VoIP VLAN 3 for port 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# auto-voip 3 37.3 auto- - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 355
interface range gigabitEthernet / interface port-channel / interface range port-channel) Example Instruct voice devices that are connected to port 3 to send the packets according to its own configuration: T2600G-52TS(config)# interface gigabitEthernet 1/0/3 T2600G-52TS(config-if)# auto-voip none 332 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 356
the Auto VoIP function on port 1/0/3: T2600G-52TS(config)# interface gigabitEthernet 1/0/3 T2600G-52TS(config-if)# no auto-voip 37 from 0 to 63. By default, it is 0. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 357
the 802.1p priority of the packets. untrust--In this mode, the switch will ignore the 802.1p priority in the voice packets and put the packets in TC-5 directly. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 358
Displays the Auto VoIP configuration information of ports. When no parameter is entered, displays the global Auto VoIP configuration information. Command Mode Privileged EXEC Mode and any Configuration Mode Example Displays the global Auto VoIP configuration information: T2600G-28TS (config)# show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 359
Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the access control mode as IP-based: T2600G-28TS(config)# user access-control ip-based enable 38.2 user access-control ip-based Description The user access-control ip-based command is used - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 360
specified IP-based entry. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the access-control of the user whose IP address is 192.168.0.148: T2600G-28TS(config)# user access-control ip-based 192.168.0.148 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 361
to be deleted. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to login: T2600G-28TS(config)# user access-control mac-based 00:00:13 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 362
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the access control mode as Port-based: T2600G-28TS(config)# user access-control port-based enable 38.6 user access-control port-based Description The user access-control port-based command is - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 363
be deleted. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the users connected to ports 2-6 are allowed to login: T2600G-28TS(config)# user access-control port-based interface gigabitEthernet - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 364
Text Transfer Protocol over Secure Socket Layer), you can manage the switch through a standard browser. HTTP is the protocol to exchange or transfer Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable the HTTP function: T2600G- - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 365
The ip http port command is used to configure the port number of the HTTP server within the switch. To set the number to the default 1800: T2600G-28TS(config)# ip http port 1800 39.3 ip http max-users Description The ip http max-users command is used to configure the maximum number of users that are - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 366
Only Admin and Operator level users have access to these commands. Example Configure the maximum number of the Admin, Operator, Power User and User users logging on to the HTTP server as 1, 2, 3 and 4 respectively: T2600G-28TS(config)# ip http max-users 1 2 3 4 39.4 ip http session timeout - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 367
Operator and Power User level users have access to these commands. Example Disable the HTTP function: T2600G-28TS(config)# no ip http secure-server 39.6 ip http secure-port Description The ip http secure-port command is used to configure the port number of the HTTPS server within the switch. To set - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 368
as 2800: T2600G-28TS(config)# ip http port 2800 39.7 ip http secure-protocol Description The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports all the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 369
to use on an SSL connection. By default, the switch supports all these ciphersuites. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the ciphersuite to be used for encryption over the SSL - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 370
less than 16. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of the Admin, Operator, Power User and User as 5, 1, 1, 1 for HTTPs: T2600G-28TS(config)# ip http secure-max - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 371
By default, the value is 10. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the timeout time of the HTTPs connection as 15 minutes: T2600G-28TS(config)# ip http secure-session timeout 15 39 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 372
supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users the IP address of fe80::1234 T2600G-28TS(config)# ip http secure-server to download an SSL key to the switch from TFTP server. Syntax ip http - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 373
, session timeout, access-control, max-user number and the idle-timeout, etc. Syntax show ip http configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of the HTTP server: T2600G-28TS(config)# show ip http - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 374
secure-server command is used to display the global configuration of SSL. Syntax show ip http secure-server Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of SSL: T2600G-28TS(config)# show ip http secure-server 351 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 375
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the SSH function: T2600G-28TS(config)# ip ssh server 40.2 ip ssh port Description The ip ssh port command is used to configure the port for SSH service. To set the value to the default - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 376
from 1 to 65535. The default value is 22. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the SSH port number as 22: T2600G-28TS(config)# ip ssh port 22 40.3 ip ssh version Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 377
HMAC-SHA1 | HMAC-MD5 -- Specify the SSH algorithm. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the SSH algorithm as AES128-CBC: T2600G-28TS(config)# ip ssh algorithm AES128-CBC 40.5 ip ssh - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 378
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the idle-timeout time of SSH as 30 seconds: T2600G-28TS(config)# ip ssh timeout 30 40.6 ip ssh max-client Description The ip ssh max-client - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 379
are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users named ssh-key from TFTP server with the IP address fe80::1234: T2600G-28TS(config)# ip ssh download v1 ssh-key ip-address fe80::1234 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 380
Mode Privilege Requirement Only Admin level users have access to these commands. Example Remove the SSH-1 type public key from the switch: T2600G-28TS# remove public-key v1 40.9 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH. Syntax show ip ssh - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 381
in. Command Mode Privileged EXEC Mode Privilege Requirement None. User Guidelines Make sure the switch can access the device, and the device can be logged in via telnet. Example Log in to a device with the IP address of 192.168.0.10: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 382
port Parameter port--The number of telnet port. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the telnet port number as 566: T2600G-28TS(config)# telnet port 566 41.4 show telnet-status Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 383
Syntax show telnet-status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display whether the Telnet function is enabled: T2600G-28TS(config)# show telnet-status 360 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 384
baud-rate Description The serial_port baud-rate command is used to configure the communication baud rate on the console port. To return to is 38400 bps. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 385
the authentication methods and their sequence to authenticate a user. The switch supports Login List for users to gain access to the switch, and Enable List for normal users to gain administrative privileges. ■ RADIUS/TACACS+ Server User can configure the RADIUS/TACACS+ servers for the connection - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 386
can copy from another switch's configuration file. The key or encrypted-key you configured here will be displayed in the encrypted form. Always configure the key as the last item of this command. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 387
Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the information of all the TACACS+ servers: T2600G By deault it is 1813. time -- Specify the time in seconds the switch waits for the server's response before it times out. The time ranges - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 388
can copy from another switch's configuration file. The key or encrypted-key you configured here will be displayed in the encrypted form. Always configure the key as the last item of this command. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 389
type as RADIUS or TACACS+. group-name -- Specify the server group name. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create a RADIUS server group with the name radius1: T2600G-28TS(config)# aaa group radius radius1 366 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 390
's IP address. Command Mode Server Group Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create the RADIUS server 1.1.1.1 to RADIUS server group "radius1": T2600G-28TS(config)# aaa group radius radius1 T2600G-28TS(aaa-group)# server 1.1.1.1 43 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 391
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the information of all the server groups: T2600G-28TS(config)# show aaa group 43.8 aaa authentication login Description This aaa authentication - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 392
Admin level users have access to these commands. User Guidelines By default the login authentication method list is "default" with "local" as method1. Example Configure a login authentication method list "list1" with the priority1 method as radius and priority2 method as local: T2600G-28TS(config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 393
Only RADIUS server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1x authentication method as "radius1": T2600G-28TS(config)# aaa - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 394
server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1x accounting method as "radius1": T2600G-28TS(config)# aaa accounting - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 395
list type. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the information of the default 802.1x accounting method list: T2600G-28TS(config)# show aaa accounting 43.14 line telnet Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 396
"local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the telnet terminal line as "list1": T2600G-28TS(config)#line telnet T2600G-28TS(config-line)# login authentication - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 397
to apply the authentication list. Syntax line ssh Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enter the ssh terminal line configuration mode: T2600G-28TS(config)#line ssh 43.17 login authentication (ssh) Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 398
authentication list. Syntax line console line-number Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enter the console 0 terminal line configuration mode: T2600G-28TS(config)#line console 0 43.19 login authentication (console - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 399
the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the console 0 terminal line as "list1": T2600G-28TS(config)# line console 0 T2600G-28TS(config-line)# login - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 400
method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the ssh terminal line as "list2": T2600G-28TS(config)# line ssh T2600G-28TS(config-line)# enable authentication - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 401
the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the console 0 terminal line as "list2": T2600G-28TS(config)# line console 0 T2600G-28TS(config-line)# enable - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 402
, which contains the method "local". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the HTTP access as "list1": T2600G-28TS(config)# ip http login authentication list1 43.24 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 403
Syntax show aaa global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the AAA function's global status and each application's method list: T2600G-28TS(config)# show aaa global 43.26 enable admin - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 404
another switch's configuration file. After the encrypted password is configured, Configuration Mode Privilege Requirement Only Admin level users have access to these commands. User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 405
from another switch's configuration file. After the encrypted password is configured, you configured password will take effect. Example Set the Enable password as "abc123" and unencrypted for users to change the access level to admin. The password will be displayed in the encrypted form. T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 406
Syntax enable-admin Command Mode Privileged EXEC Mode Privilege Requirement Only User, Power User and Operator level users have access to these commands. Example Get the administrative privilege (the Enable password is "123456"): T2600G-28TS# enable-admin Password: 123456 383 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 407
supplicant. It is usually an 802.1x-supported network device, such as this TP-Link switch. It acts as an intermediary (proxy) Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IEEE 802.1x function: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 408
the switch. Please disable the handshake feature if you are using a non-TP-Link 802.1x-compliant client software. This feature is enabled by default. Syntax dot1x handshake no dot1x handshake Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 409
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the Authentication protocol of IEEE 802.1x as "pap": T2600G . If the assigned VLAN exists on the switch, the switch will directly add the authenticated port to the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 410
vlan-assignment no dot1x vlan-assignment Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the VLAN assignment feature: T2600G-28TS(config)#dot1x vlan-assignment 44.5 dot1x accounting Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 411
and Power User level users have access to these commands. Example Enable the MAB feature on the Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config)#dot1x mab 44.7 dot1x guest-vlan Description The dot1x guest-vlan command is used to configure the Guest - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 412
is disabled. The supplicants in the Guest VLAN can access the specified network source. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Guest VLAN function for VLAN 5 and set the VLAN - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 413
time for the switch to wait for the response from supplicant before resending a request to the supplicant., ranging from 1 to 60 in second. By default, it is 30 seconds. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 414
Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum transfer times of the repeated authentication request as 5 on the Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config)#dot1x max-req - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 415
Power User level users have access to these commands. Example Enable the IEEE 802.1x function for the Gigabit Ethernet port 1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#dot1x 44.12 dot1x port-control Description The dot1x port-control command is used to configure the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 416
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the Control Mode for Gigabit Ethernet port 20 as "authorized-force": T2600G-28TS(config)#interface gigabitEthernet 1/0/20 T2600G-28TS(config-if)#dot1x port-control authorized-force - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 417
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the Control Type for Gigabit Ethernet port 20 as "port-based": T2600G-28TS(config)#interface gigabitEthernet 1/0/20 T2600G-28TS(config-if)#dot1x port-method port-based 44.14 dot1x - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 418
The show dot1x global command is used to display the global configuration of 801.X. Syntax show dot1x global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of 801.X globally: T2600G-28TS(config)#show dot1x global 395 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 419
Mode Privilege Requirement None. Example Display the configuration information of 801.X for Gigabit Ethernet port 20: T2600G-28TS(config)#show dot1x interface gigabitEthernet 1/0/20 Display the configuration information of 801.X for all Ethernet ports: T2600G-28TS(config)#show dot1x interface 44.18 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 420
Example Display the authentication status of each port: T2600G-28TS(config)#show dot1x auth-state 397 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 421
, Operator and Power User level users have access to these commands. Example Set the maximum number of MAC addresses that can be learned on port 1/0/1 as 30, enable exceed-max-leaned feature and configure the mode as permanent and the status as drop: T2600G-28TS (config)#interface gigabitEthernet - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 422
port | gigabitEthernet port | ten-gigabitEthernet port } Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the port security configuration on port 1/0/1 T2600G-28TS# show mac address-table max-mac-count interface gigabitEthernet 1/0/1 399 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 423
The monitoring port number. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Create monitor session 1 and configure port 1/0/1 as the monitoring port: T2600G-28TS(config)# monitor session 1 destination interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 424
1: T2600G-28TS(config)# no monitor session 1 46.2 monitor session source Description The monitor session source command is used to configure the to the monitoring port. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. 401 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 425
User Guidelines 1. The monitoring port is corresponding to current interface configuration mode. 2. Monitored ports number is not limited, but cannot be link-aggregation member. Example Create monitor session 1, then configure port 4, 5, 7 as monitored port and enable ingress monitoring: T2600G-28TS( - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 426
T2600G-28TS(config)# show monitor session 1 403 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 427
Content ACL are from 2000 to 2499. Note: T2600G-18TS does not support Packet Content ACL. acl-name -- Enter a name to identify the ACL. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an IP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 428
, and so on, for the rest of the offset value. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure a packet content profile with offset 0,1,2,3: T2600-28TS(config)# access-list packet-content - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 429
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Resequence the rules of ACL 12 with the start ID as 1 and step value as 5: T2600G-28TS(config)# access-list resequence 12 1 step 5 47.4 access-list mac - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 430
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create MAC ACL 50 and configure Rule 5 to permit packets with source MAC address 00:34:a2:d4:34:b5: T2600G-28TS (config)#access-list create 50 T2600G-28TS (config-mac-acl)#access-list mac - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 431
to all fragmented packets and always permit to forward the last fragment of a packet. Note: frag {enable | disable} is not available for T2600G-18TS. protocol -- Specify a protocol type. s-port-number -- Specify the source port number. s-port-mask -- Specify the source port mask with 4 hexadecimal - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 432
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create IP ACL 600, and configure Rule 1 to permit packets with source IP address 192.168.1.100: T2600G-28TS (config)#access-list create 600 T2600G-28TS (config)#access-list ip 600 rule - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 433
MAC address is entered. vlan-id: The VLAN ID ranges from 1 to 4094. ether-type -- Specify the Ethernet-type with 4 hexadecimal numbers. priority -- The user priority ranges from 0 to 7. The default is No Limit. source-ip: Enter the source IP address. source-ip-mask -- Enter the mask of the source - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 434
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create Combined ACL 1100 and configure Rule 1 to deny packets with source IP address 192.168.3.100 in VLAN 2: T2600G-28TS(config)# access-list create 1100 T2600G-28TS(config)# access-list combined 1100 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 435
Parameter acl-id-or-name -- Enter the ID or name of the ACL that you want to add a rule for. auto -- The rule ID will be assigned automatically and the interval between rule IDs is 5. rule-id -- Assign an ID to the rule. deny | permit -- Specify the action to be taken with the packets that match the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 436
User level users have access to these commands. User Guidelines Before binding an IPv6 ACL to a VLAN or interface, you should configure the SDM template as "enterpriseV6" and save your configurations. Example Create IPv6 ACL 1600 and configure config Note: T2600G-18TS does not support Packet Content - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 437
byte hex mode, like '0000ffff'. time-segment -- The name of the time-range. The default is No Limit. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a packet-content ACL rule with all 4 chunks - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 438
Enter the ID of the ACL rule. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the rule 1 of ACL 200 to be configured with policies: T2600G-28TS(config)# access-list action 200 1 47.10 redirect - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 439
ranges from 0 to 63. Note: Remark DSCP is not available for T2600G-18TS. Command Mode Action Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure a policy for rule 1 of ACL 6: limit the transmission rate of the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 440
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure a policy for rule 1 of ACL 6: specify the mirror port as Gigabit Ethernet port 1/0/2 for the data packets matching this rule: T2600G-28TS(config)#access-list action 6 rule - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 441
Only Admin, Operator and Power User level users have access to these commands. Example Configure a policy for rule 1 of ACL 6: specify the DSCP region as 30 and local priority 2 for the packets matching this rule: T2600G-28TS(config)#access-list action 6 rule 1 T2600G-28TS(config-action)# qos-remark - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 442
that you want to bind the ACL to. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind ACL 1 to port 3 and VLAN 4: T2600G-28TS(config)#access-list bind 1 interface vlan 4 gigabitEthernet 1/0/3 47.15 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 443
of ACL entry resource. Syntax show access-list status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the usage status of ACL entry resource: T2600G-28TS(config)# show access-list status 47.18 show access-list counter Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 444
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the packet counter of ACL 100: T2600G-28TS(config)# show access-list 100 counter 47.19 clear access-list Description The clear access-list command is used to clear the counter of - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 445
command is used to bind the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port number together in the condition -addr -- The IP address of the entry to be deleted. Command Mode Global Configuration Mode 422 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 446
for automatic binding. Syntax ip dhcp snooping no ip dhcp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Snooping function globally: T2600G-28TS(config)#ip dhcp snooping 423 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 447
function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Snooping function on VLAN 1, 4, 6-7: T2600G-28TS(config)#ip dhcp snooping vlan 1,4,6-7 48.4 ip dhcp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 448
-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of entries that can be learned on port 1 as 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#ip dhcp snooping max-entries - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 449
status of DHCP Snooping. Syntax show ip dhcp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the running status of DHCP Snooping: T2600G-28TS#show ip dhcp snooping 48.7 show ip dhcp snooping interface Description The show ip dhcp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 450
Example Display the DHCP Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ip dhcp snooping interface Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ip dhcp snooping interface gigabitEthernet 1/0/5 427 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 451
is used to bind the IPv6 address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IPv6 address, MAC address, VLAN ID and the Port number together in the condition Ipv6-addr -- The IPv6 address of the entry to be deleted. Command Mode Global Configuration Mode 428 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 452
binding. Syntax Ipv6 dhcp snooping no ipv6 dhcp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCPv6 Snooping function globally: T2600G-28TS(config)#ipv6 dhcp snooping 429 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 453
function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCPv6 Snooping function on VLAN 1, 4, 6-7: T2600G-28TS(config)#ipv6 dhcp snooping vlan 1,4,6-7 49.4 ipv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 454
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of entries that can be learned on port 1 as 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#ipv6 dhcp snooping max-entries - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 455
function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the ND snooping function on VLAN 1,4,6-7: T2600G-28TS(config)#ipv6 nd snooping vlan 1,4,6-7 49.7 ipv6 nd - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 456
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of binding entries from ND Snooping of Gigabit Ethernet port 1/0/2 is 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ipv6 nd snooping max - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 457
of DHCPv6 Snooping. Syntax show ipv6 dhcp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the running status of DHCPv6 Snooping: T2600G-28TS#show ipv6 dhcp snooping 49.10 show ipv6 dhcp snooping interface Description The show ipv6 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 458
Privilege Requirement None. Example Display the DHCPv6 Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ipv6 dhcp snooping interface Display the DHCPv6 Snooping configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ipv6 dhcp snooping interface gigabitEthernet - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 459
number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the ND Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ipv6 nd snooping interface Display the ND Snooping - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 460
. 50.1 ip verify source Description The ip verify source command is used to configure the IP Verify Source mode for a specified port. To disable the IP Verify Source function, please use no ip verify source command. Syntax For T2600G-18TS: ip verify source { sip | sip+mac } no ip verify source For - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 461
source logging Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the log feature to make the switch generate logs when receiving illegal packets: T2600G-28TS(config)#ip verify source logging - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 462
Syntax show ip verify source Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IP Verify Source configuration information: T2600G-28TS(config)#show ip verify source 50.4 show ip verify source interface Description The show ip verify source - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 463
to the IPv6-MAC binding rules can be processed. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IPv6 Verify Source function - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 464
information. Syntax show ipv6 verify source Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IPv6 Verify Source configuration information: T2600G-28TS(config)#show ipv6 verify source 51.3 show ipv6 verify source interface Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 465
Privilege Requirement None. Example Display the IPv6 verify source configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ipv6 verify source interface gigabitEthernet 1/0/5 442 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 466
. Syntax ip dhcp filter no ip dhcp filter Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Filter function globally: T2600G-28TS(config)#ip dhcp filter 52.2 ip dhcp filter (interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 467
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Filter on port 1/0/1 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 468
stands for "disable". Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet User level users have access to these commands. Example Set the Flow Control of GigabitEthernet port 2 as 20 pps: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 469
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the rate limit of DHCP Decline packets as 20 packets per second on Gigabit Ethernet port 1/0/2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ip dhcp filter - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 470
list | port-channel-id -- Specify the port that the legal DHCPv4 server is connected to. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an entry for the legal DHCPv4 server whose IP address is - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 471
port | port-channel port-channel-id ] Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCP Filter configuration on port 1/0/3: T2600G-28TS#show ip dhcp filter interface gigabitEthernet 1/0/3 52.9 show ip dhcp filter server permit - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 472
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the legal DHCP server configuration: T2600G-28TS#show ip dhcp filter server permit-entry 449 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 473
Ipv6 dhcp filter no ipv6 dhcp filter Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCPv6 Filter function globally: T2600G-28TS(config)#ipv6 dhcp filter 53.2 ipv6 dhcp filter (interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 474
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCPv6 Filter on port 1/0/1 T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 475
port 2 as 20 pps: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ipv6 dhcp filter limit rate 20 53.4 ipv6 dhcp filter decline rate Description The ipv6 dhcp filter decline rate command is used to enable the Decline Protect feature and configure the rate limit on DHCP - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 476
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an entry for the legal DHCPv6 server whose IP address is 192.168.0.100 and connected port number is 1/0/1: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 477
of DHCPv6 Filter. Syntax show ipv6 dhcp filter Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCPv6 Filter configuration: T2600G-28TS#show ipv6 dhcp filter 53.7 show ipv6 dhcp filter interface Description The show ipv6 dhcp filter - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 478
command is used to display the legal server configuration. Syntax show ipv6 dhcp filter server permit-entry Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the legal DHCPv6 server configuration: T2600G-28TS#show ipv6 dhcp filter server permit - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 479
programs sending a lot of service requests to the Host. With the DoS Defend enabled, the switch can analyze the specific Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DoS defend function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 480
Syntax For T2600G-18TS: ip dos-prevent type { land | scan-synfin | xma-scan | null-scan 1024 | blat | ping-flood | syn-flood | win-nuke | ping-of-death | xma-scan } For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: ip dos-prevent type { land | scan-synfin | xma-scan | null-scan | port-less-1024 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 481
computer. Note: Only T2600G-18TS supports Ping of Death. smurf -- Smurf attack is a distributed denial-of-service attack in which large : Only T2600G-18TS supports Smurf Attack. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 482
Syntax show ip dos-prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DoS information of the detected DoS attack globally: T2600G-28TS(config)#show ip dos-prevent 459 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 483
55. sFlow Commands (Only for Certain Devices) Note: T2600G-18TS does not support sFlow. sFlow (Sampled Flow) is a technology for accurately monitoring network traffic at high speeds. The sFlow monitoring system consists of a sFlow agent (embedded in a switch or router or in a standalone probe) and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 484
Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. User Guidelines A valid agent address should be assigned to the sFlow agent embedded in the switch before you enable the sFlow function. Example Enable sFlow function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 485
Global Configuration Mode Privilege Requirement Only Admin and Operator level users have T2600G-28TS(config)# sflow collector collector-ID 1 ip 192.168.0.100 T2600G-28TS(config)# sflow collector collector-ID 1 port 3000 55.4 sflow sampler Description The sflow sampler command is used to configure - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 486
Requirement Only Admin and Operator level users have access to these commands. Example Configure Gigabit Ethernet port 1 as the sFlow sampler: specify the Collector-ID as 1, the ingress rate as 1024: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#sflow sampler collector - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 487
sFlow collector. Syntax show sflow collector Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of the sFlow collector: T2600G-28TS#show sflow collector 55.7 show sflow sampler Description The show sflow sampler command - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 488
troubleshooting users have access to these commands. Example Enable the Ethernet OAM function for Gigabit Ethernet port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ethernet-oam 56.2 ethernet-oam mode Description The ethernet-oam mode command is used to configure - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 489
and Operator level users have access to these commands. Example Configure Ethernet OAM client to operate in passive mode for Gigabit Ethernet port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ethernet-oam mode passive 56.3 ethernet-oam link-monitor symbol-period - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 490
level users have access to these commands. Example For error symbol-period event, configure the error threshold as 5 and the event detection interval as 3 seconds on Gigabit Ethernet port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ethernet-oam link-monitor - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 491
Operator level users have access to these commands. Example For error frame event, configure the error threshold as 6 and the event detection interval as 9 seconds on Gigabit Ethernet port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ethernet-oam link-monitor - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 492
level users have access to these commands. Example For error frame period event, configure the error threshold as 6 and the event detection interval as 150000 frames on Gigabit Ethernet port 1/0/4: T2600G-28TS(config)# interface gigabitEthernet 1/0/4 T2600G-28TS(config-if)# ethernet-oam link-monitor - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 493
level users have access to these commands. Example For error frame seconds event, configure the error threshold as 8 and the event detection interval as 30 seconds on Gigabit Ethernet port 5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# ethernet-oam link-monitor - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 494
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable the Dying Gasp link event notification on Gigabit Ethernet port 1/0/7: T2600G-28TS(config)# - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 495
the remote peer to stop the Ethernet OAM remote loopback mode. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Request the remote peer to start the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 496
of all ports are cleared. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Clear Ethernet OAM statistics of Gigabit Ethernet port 1/0/3: T2600G-28TS(config)# clear ethernet-oam statistics interface gigabit - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 497
Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display Ethernet OAM configuration information of Gigabit Ethernet port 1/0/2: T2600G-28TS(config)# show ethernet-oam configuration interface gigabitEthernet 1/0/2 474 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 498
ports are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display Ethernet OAM event log of Gigabit Ethernet port 1/0/2: T2600G-28TS(config)# show ethernet-oam event-log interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 499
displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display Ethernet OAM status of Gigabit Ethernet port 1/0/2: T2600G-28TS(config)# show ethernet-oam status interface gigabitEthernet - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 500
unidirectional link is detected, the corresponding port will be shut down automatically or manually (depending on the shut mode configured). 57 Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the DLDP function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 501
detected. By default, the shut-mode is auto. manual --The switch displays an alert when a unidirectional link is detected. The operation to shut down the unidirectional link ports is accomplished by the users. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 502
to reset all the unidirectional links and restart the link detect process. Syntax dldp reset Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Reset the DLDP function globally: T2600G-28TS(config)# dldp reset 57 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 503
the link detect process. Syntax dldp reset Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Reset the DLDP function of ports 2-4: T2600G-28TS - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 504
number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration and state of all ports: T2600G-28TS# show dldp interface Display the configuration and state of port 1/0/5: T2600G-28TS# show dldp interface gigabitEthernet 1/0/5 481 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 505
use no snmp-server command. Syntax snmp-server no snmp-server Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the SNMP function: T2600G-28TS(config)# snmp-server 58.2 snmp-server view Description The snmp-server view - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 506
Mode Privilege Requirement Only Admin level users have access to these commands. Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station: T2600G-28TS(config)# snmp-server view view1 1.3.6.1.6.3.20 include 58.3 snmp - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 507
receive notification messages of the assigned SNMP view generated by the switch's SNMP agent. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Add a group, and configure the name as group 1, the Security Model as SNMP v3, the - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 508
is connected to a local SNMP engine, while remote means that the user is connected to a remote SNMP engine. As the remote engine ID and user password are used to compute the authentication and privacy digests, before configuring a remote user, you need to set the remote engine ID first. group-name - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 509
group2, and configure the Security Model of the user as v3, the Security Level of the group as authPriv, the Authentication Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: T2600G-28TS(config)# snmp-server user admin local - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 510
to access. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example ] no snmp-server host ip user-name Parameter ip -- The IP Address of the management Host. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 511
Retry times. timeout -- The maximum time for the switch to wait for the response from the management station before resending a request, ranging from 1 to 3600 in seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Add - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 512
, and the retries time as 100: T2600G-28TS(config)# snmp-server host fe80::1234 162 admin smode v2c type inform retries 100 timeout 1000 58.7 snmp-server engineID Description The snmp-server engineID command is used to configure the local and remote engineID of the switch. To restore to the default - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 513
remote engineID as abcdef123456: T2600G-28TS(config)# snmp-server switch system. The trap can be triggered when you reboot the switch. auth-failure -- Triggered when a received SNMP request fails the authentication. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 514
Example Enable SNMP standard linkup trap for the switch: T2600G-28TS(config)# snmp-server traps snmp linkup 58.9 CPU utilization rate for the switch is 80% by default. flash --Triggered when flash is modified during operations such as backup, reset, firmware upgrade, configuration import, and so on. - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 515
Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP extended bandwidth-control trap for the switch: T2600G-28TS(config)# snmp-server traps bandwidth-control 58.10 snmp-server traps ddm Note: Only T2600G-18TS, T2600G-28TS and - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 516
to disable all the types of DDM traps. For more instructions about the alarm threshold or warning threshold, refer to Chapter 11 DDM Commands. Command Mode Global Configuration Mode Example Enable all the SNMP DDM traps for the switch: T2600G-28TS(config)# snmp-server traps ddm 58.11 snmp-server - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 517
when certain VLANs are deleted successfully. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable all SNMP extended VLAN-related traps for the switch: T2600G-28TS(config)# snmp-server traps vlan Enable VLAN-created - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 518
. Syntax snmp-server traps acl no snmp-server traps acl Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the ACL trap for the switch: T2600G-28TS(config)# snmp-server traps acl 58.14 snmp-server traps ip Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 519
Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the IP-Change trap for the switch: T2600G-28TS(config)# snmp-server traps ip change 58.15 snmp-server traps power Note: Only T2600G-28MPS supports this command. Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 520
power in this case. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable all PoE traps for the switch: T2600G-28MPS(config)# snmp-server traps power 58.16 snmp-server traps link-status Description The snmp-server traps - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 521
users have access to these commands. Example Enable SNMP link status trap for port 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# snmp-server traps link-status 58.17 rmon history Description The rmon history command is used to configure configured, the switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 522
T2600G-28TS(config)# rmon history 1-3 interface gigabitEthernet 1/0/2 interval 100 owner owner1 58.18 rmon event Description The rmon event command is used to configure . You can only select one entry for each command. user-name -- The name of the User to which the event belongs, ranging from 1 to 16 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 523
as Description1, the type of event as log and the owner of the event as owner1: T2600G-28TS(config)# rmon event 1-4 user user1 Description Description1 type log owner owner1 58.19 rmon alarm Description The rmon alarm command is used to configure SNMP-RMON Alarm Management. To return to the default - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 524
Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds: T2600G-28TS(config)#rmon alarm 1-3 stats-index 2 owner owner1 interval 100 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 525
Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the statistics entries 1-3 with the statistics port as 1/0/1, owner as owner1 and status as valid: T2600G-28TS(config)#rmon statistics 1-3 interface gigabitEthernet 1/0/1 owner owner1 status - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 526
the View table. Syntax show snmp-server view Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the View table: T2600G-28TS# show snmp-server view 58.23 show snmp-server group Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 527
command is used to display the User table. Syntax show snmp-server user Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the User table: T2600G-28TS# show snmp-server user 58.25 show snmp-server - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 528
the SNMP. Syntax show snmp-server engineID Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the engineID: T2600G-28TS# show snmp-server engineID 58.28 show rmon history Description The show rmon - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 529
sample entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of all history sample entries: T2600G-28TS# show rmon history 58.29 show rmon event Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 530
entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the Alarm Management entry 1-2: T2600G-28TS# show rmon alarm 1-2 58.31 show rmon statistics Description - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 531
Example Display the configuration of the statistics entry 1: T2600G-28TS#show rmon statistics 1 508 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 532
Commands (Only for Certain Devices) Note: Only T2600G-28MPS supports PoE function. PoE (Power over Ethernet) technology is 384. Command Mode Global Configuration Mode Privilege Requirement None. Example Configure the max power the PoE switch can supply as 160w: T2600G-28MPS(config)# power inline - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 533
system power limit, the PD linked to the port with lower manually enter a value ranging from 1 to 300. The value is in the unit of 0.1 watt. For instance, if you want to configure the max power as 5w, you should enter 50. "Auto" indicates the value is assigned automatically by the PoE switch - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 534
switch. "Class1" represents 4w. "Class2" represents 7w. "Class3" represents 15.4w. "Class4" represents 30w. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement None. Example Configure the power limit as "5w" for port 2: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 535
the PoE priority as "low" for port 2: T2600G-28MPS(config)# interface gigabitEthernet 1/0/2 T2600G-28MPS(config-if)# power inline priority low 59.5 power inline supply Description The power inline supply command is used to configure the PoE status of the corresponding port. Syntax power inline - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 536
spaces then put it inside double quotes. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement None named "IP Camera" to port 2: T2600G-28MPS(config)# interface gigabitEthernet 1/0/2 T2600G-28MPS(config-if)# power inline profile - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 537
Requirement None. Example Display the PoE information of the system: T2600G-28MPS# show power inline 59.9 show power inline configuration interface Description The show power inline configuration interface command is used to display the PoE configuration of the certain port. Syntax show power inline - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 538
port ] Parameter port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the PoE information of all ports: T2600G-28MPS# show power inline information interface 59.11 show power profile Description The show power - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 539
Example Display the defined PoE profile: T2600G-28MPS# show power profile 516 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 540
(Address Resolution Protocol) Detect function is to protect the switch from the ARP cheating, such as the Network Gateway Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the ARP Detection function globally: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 541
reply packets are legal. The illegal packets will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the switch to check whether the source MAC address and the sender MAC address are - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 542
use no ip arp detection trust command .The specific ports, such as up-linked port and routing port and LAG port, should be set as Trusted Port. To ensure the normal communication of the switch, please configure the ARP Trusted Port before enabling the ARP Detect function. Syntax ip arp inspection - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 543
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum amount of the received ARP packets per second as 50 pps for Gigabit Ethernet port 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)#ip arp inspection - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 544
) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the burst interval as 2 seconds for Gigabit Ethernet port 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)#ip arp inspection burst-interval - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 545
Trusted Port list. Syntax show ip arp inspection Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the ARP detection configuration globally: T2600G-28TS(config)#show ip arp inspection 60.9 show ip arp inspection interface Description The show - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 546
ARP detection. Syntax show ip arp inspection vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the ARP Inspection configuration of VLAN: T2600G-28TS(config)#show ip arp inspection vlan 60.11 show ip arp inspection statistics Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 547
statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear the statistic of the illegal ARP packets received: T2600G-28TS(config)#clear ip arp inspection statistics 524 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 548
switch to detect the ND packets based on the binding entries in the IPv6-MAC Binding Table and filter out the illegal ND packets. Before configuring ND Detection, complete IPv6-MAC Binding configuration Global Configuration Mode Example Enable the ND Detection function globally: T2600G-28TS(config - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 549
Mode Global Configuration Mode Example Enable the Log function on VLAN 1,4,6-7: T2600G-28TS( configure the port for which the ND Detection function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no ipv6 nd detection trust command .The specific port, such as up-linked - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 550
switch, please configure the ND Detection Trusted Port before enabling the ND Detection function. Syntax Ipv6 nd detection trust no ipv6 nd detection trust Command Mode Interface Configuration and Any Configuration Mode Example Display the ND Detection configuration globally: T2600G-28TS(config)# - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 551
Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#show ipv6 nd detection interface gigabitEthernet 1/0/1 Display the configuration of all Ethernet ports: T2600G-28TS(config)#show ipv6 nd detection interface - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 552
ipv6 nd detection vlan command is used to display the VLAN configuration of ND Detection. Syntax show ipv6 nd detection vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ipv6 ND Detection configuration of VLAN. T2600G-28TS(config)#show ipv6 nd detection vlan 529 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 553
It will be lost when the switch is restarted. Syntax logging buffer no logging buffer Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the system log buffer: T2600G-28TS(config)#logging buffer 62.2 logging - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 554
Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Set the severity level as 5: T2600G-28TS( log file of the flash will not be lost after the switch is restarted and can be got by the show logging flash command. Syntax - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 555
of the flash and is not recommended. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify the log file synchronization frequency as 10 hours: T2600G-28TS(config)#logging file flash frequency periodic10 532 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 556
Admin and Operator level users have access to these commands. Example Save the log messages with their severities equal or higher than 7 to the flash : T2600G-28TS(config)#logging file flash level 7 62.6 logging host index Description The logging host index command is used to configure the Log Host - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 557
index of the log host. The switch supports 4 log hosts at most. host- Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable log host 2 and set its IP address as 192.168.0.148, the level 5: T2600G - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 558
Example Enable logging to the console port: T2600G-28TS(config)# logging console 62.8 logging console level will be output to the terminal devices. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Output the log - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 559
by default. Syntax logging monitor no logging monitor Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable logging to the terminal devices: T2600G-28TS(config)# no logging monitor 62.10 logging monitor level - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 560
: buffer and flash. Clear the information of the two channels, by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Clear the information in the log file: T2600G-28TS(config)# clear logging buffer 537 - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 561
and the log file. Syntax show logging local-config Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the Local Log: T2600G-28TS(config)# show logging local-config 62.13 show logging loghost Description The show logging - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 562
information in the log buffer by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the log information from level 0 to level 5 in the log buffer: T2600G-28TS(config)# show logging buffer level 5 62.15 show logging flash Description The - TP-Link T2600G-28SQ | T2600G Series Switches CLI Reference Guide Guide - Page 563
lower than the select level will display. Display all the log information in the log file by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the log information with the level marked 0-3 in the log file
CLI Reference Guide
T2600G-18TS /T2600G-28TS (TL-SG3424) /T2600G-28TS-DC/
T2600G-28MPS (TL-SG3424P) / T2600G-28SQ/ T2600G-52TS (TL-SG3452)
1910012658 REV4.2.0
December 2019