Xerox 8200B Network Users Guide - Page 43

UNIX/Linux Network, Overview, Quick install steps

Get Xerox 8200B - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 095205082128
View all Xerox 8200B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Phaser® 8200 Color Printer UNIX/Linux Network This section provides installation and troubleshooting steps for UNIX and Linux: I Overview - see page 38. I Quick install steps - see page 38. I Additional resources - see page 39. Overview Your Phaser printer supports connection to a variety of UNIX platforms. Below is a list of the currently supported versions: I Solaris I IBM AIX I Hewlett-Packard HP-UX I DEC UNIX I True UNIX 64 (Compaq) I Linux (i386) I Linux (PPC) I SGI The procedures contained in this document enable you to connect your printer using any of the supported versions of UNIX or Linux listed above. Quick install steps 1. Print the Configuration Pages and retain them for reference. For information on printing Configuration Pages, see the Front Panel chapter of the Phaser 8200 Color Printer User Guide on the Software and Documentation CD-ROM. 1. Check the Configuration Pages and verify that both TCP/IP protocol and the proper connector are enabled. 2. Go to the section IP Address and perform one of the procedures there, depending on the manner in which you want to set your printer's IP address. 3. Solaris: Refer to the CentreWare Services for Unix Systems User Guide (English only) included on the Advanced Network Management Tools CD-ROM for CentreWare installation and detailed printer setup instructions. Other UNIX OS: Load printer drivers and configure the printer for one of the Print Models. These drivers are available on the Advanced Network Management Tools CD-ROM or from the Xerox web site at www.xerox.com/officeprinting/support. Copyright © 2002 Xerox Corporation. All Rights Reserved. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Phaser
®
8200 Color Printer
Copyright © 2002 Xerox Corporation. All Rights Reserved.
38
UNIX/Linux Network
This section provides installation and troubleshooting steps for UNIX and Linux:
■
Overview
—
see page 38.
■
Quick install steps
—
see page 38.
■
Additional resources
—
see page 39.
Overview
Your Phaser printer supports connection to a variety of UNIX platforms. Below is a list of the currently
supported versions:
■
Solaris
■
IBM AIX
■
Hewlett-Packard HP-UX
■
DEC UNIX
■
True UNIX 64 (Compaq)
■
Linux (i386)
■
Linux (PPC)
■
SGI
The procedures contained in this document enable you to connect your printer using any of the
supported versions of UNIX or Linux listed above.
Quick install steps
1.
Print the Configuration Pages and retain them for reference. For information on printing
Configuration Pages, see the
Front Panel
chapter of the
Phaser 8200 Color Printer User Guide
on
the
Software and Documentation CD-ROM
.
1.
Check the Configuration Pages and verify that both TCP/IP protocol and the proper connector are
enabled.
2.
Go to the section
IP Address
and perform one of the procedures there, depending on the manner in
which you want to set your printer
’
s IP address.
3.
Solaris:
Refer to the
CentreWare Services for Unix Systems User Guide
(English only) included
on the
Advanced Network Management Tools CD-ROM
for CentreWare installation and
detailed printer setup instructions.
Other UNIX OS:
Load printer drivers and configure the printer for one of the Print Models.
These drivers are available on the
Advanced Network Management Tools CD-ROM
or from
the Xerox web site at
www.xerox.com/officeprinting/support
.