Yamaha CP50 Reference Manual - Page 32
Zone Edit Screen, Edit Sequence, Press the [COMMON] button, Navigate to using
UPC - 086792936963
View all Yamaha CP50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
Zone Edit Screen Settings are made on the Zone Edit screen when your CP5 or CP50 is to be used as a master keyboard. By setting the ZoneSw parameter to "on", you can split the keyboard into a maximum of four zones, and if these zones are then assigned to the built-in Tone Generator and external musical devices, it will be possible to play them all from the stage piano's keyboard. To access the Zone Edit screen, press Knob 3 (ZoneEdit [PUSH]) from Page 2 of the Common Settings screen. Edit Sequence Press the [COMMON] button Navigate to Page 2 using the [- PAGE] and [PAGE 3] buttons Press Knob 3 (ZoneEdit [PUSH]) Page All pages 1 2 3 4 5 6 7 On-screen name (and full name) Zone ZoneSw (Zone Switch) Target TransCh (Transmit Channel) Octave Trnsps (Transpose) NoteLimit (Note Limits) MIDIBankSel (MIDI Bank Select) MIDIPgmChg (MIDI Program Change) Volume Pan Description This parameter is used to select the zone to be edited. As Page 1 affects all zones, however, this parameter's setting is displayed as "COMMON" on that page. Setting values: zone1, zone2, zone3, or zone4 This parameter is used to turn on and off splitting of the keyboard into four distinct zones. This parameter is used to select a destination for control signals from the current zone. Setting values: off ......... The current zone will be disabled. TG......... The current zone will control the built-in Tone Generator. MIDI...... The current zone will control another musical device connected to the stage piano. both ...... The current zone will control both the built-in Tone Gen- erator and another musical device connected to the stage piano. This parameter is used to select a MIDI transmit channel for control signals from the current zone. A setting may be made only when Target is set to "MIDI" or "both". Setting values: 1 to 16 This parameter is used to transpose the current zone in units of one octave. Setting values: -3 to +0 to +3 This parameter is used to transpose the current zone in units of one semitone. Setting values: -11 to +0 to +11 (semitones) These parameters are used to define a keyboard section for the current zone. Specifically, Knob 2 is used to set the lowest note; Knob 3, the highest. Setting values: C-2 to G8 Set by turning Knobs 2 and 3, these parameters can be used to specify bank select MSB, bank select LSB, and program change values to be sent to the corresponding external musical device as MIDI messages. In this way, you can select a sound to be played by the current zone. It should be noted that the actual sounds produced will depend on the type of musical device being used. Meanwhile, if these parameters are set to "off", no bank select MSB, bank select LSB, or program change values will be send as MIDI messages from the zone in question. Setting values: MIDIBankSel...... off, 0 to 127 MIDIPgmChg..... off, 1 to 128 This parameter is used to adjust the volume of the current zone. Setting values: 0 to 127 This parameter is used to adjust the stereo panning of the current zone. Setting values: L63 to C to R63 Internal Design of the CP5 & CP50 Reference Left & Right Parts 3[VOICE] 3[PRE-AMP] 3[MOD-FX] 3[PWR-AMP] (CP5 only) 3[LEFT1]/[LEFT2]/[RIGHT1]/ [RIGHT2] (CP5) [LEFT]/[RIGHT] (CP50) 3[COMMON] Song Setting Area 3[SONG SETTING] 3[RECORD] TRACK Part 3[TRACK] MIC INPUT Part 3[MIC INPUT] (CP5 only) Settings for All Parts 3[REVERB] Settings for All Performances 3[MASTER COMPRESSOR] 3[UTILITY] 3[FILE] Appendix 32 CP5/CP50 Reference Manual