Yamaha CP50 Reference Manual - Page 40
MIC INPUT Part (CP5 only), Mic Effects Screen
UPC - 086792936963
View all Yamaha CP50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 40 highlights
MIC INPUT Part (CP5 only) This section provides a detailed description of the parameters used to configure the CP5's MIC INPUT part. The setting screen for this part contains two pages. Edit Sequence Press and hold the [MIC INPUT] button (for at least one second) Navigate to the required page using the [- PAGE] and [PAGE 3] buttons Turn or press Knobs 1 to 3 Page 1 On-screen name (and full name) Volume Pan RevSend (Reverb Send) 2 MicFx (Mic Effects) MicIns (Mic Insert Effect) Description This parameter is used to adjust the part's output level. It can also be set at any time using the [MIC INPUT] knob on the control panel. Setting values: 0 to 127 This parameter is used to adjust the part's stereo panning. Setting values: L63 (far left) to C (center) to R63 (far right) This parameter is used to set how much of the part's output signal is sent to the Reverb block. Higher values produce a more pronounced reverb sound. Setting values: 0 to 127 By pressing Knob 1 on this page, you can open the Mic Effects screen (see below) in order to configure the compressor, noise gate, and EQ that act on the microphone input. By pressing Knob 2 on this page, you can open the Mic Insert Effect screen (page 41) in order to select and configure an insertion effect for the microphone input. Mic Effects Screen From the Mic Effects screen, you can set parameters affecting the compressor, noise gate, and EQ that act on audio signals input via the MIC INPUT jack. This screen contains a total of seven pages. Edit Sequence Press and hold the [MIC INPUT] button (for at least one second) Navigate to Page 2 using the [PAGE 3] button Press Knob 1 Navigate to the required page using the [- PAGE] and [PAGE 3] buttons Turn Knobs 1 to 3 Page On-screen name (and full name) Description 1 NoiseSw This parameter is used to turn on or off the noise gate for microphone input signals. (Noise Gate Switch) Setting values: on or off CompSw (Compressor Switch) This parameter is used to turn on or off the compression of microphone input signals. Setting values: on or off 2 NoisAtk This parameter is used to set the amount of time that elapses between arrival of an (Noise Gate Attack) input signal and activation of the noise gate. Setting values: 1ms to 40ms NoisRel (Noise Gate Release) This parameter is used to set the amount of time over which the noise gate stops silencing the input signal. Setting values: 10ms to 680ms NoisTh (Noise Threshold) This parameter is used to set the level at which the noise gate starts silencing the input signal. Setting values: -73dB to -30dB 3 CompAtk This parameter is used to set the amount of time that elapses between arrival of an (Compressor Attack) input signal and activation of the compressor. Setting values: 1ms to 40ms CompRel (Compressor Release) This parameter is used to set the amount of time over which the compressor stops compressing the sound. Setting values: 10ms to 680ms 40 CP5/CP50 Reference Manual Internal Design of the CP5 & CP50 Reference Left & Right Parts 3[VOICE] 3[PRE-AMP] 3[MOD-FX] 3[PWR-AMP] (CP5 only) 3[LEFT1]/[LEFT2]/[RIGHT1]/ [RIGHT2] (CP5) [LEFT]/[RIGHT] (CP50) 3[COMMON] Song Setting Area 3[SONG SETTING] 3[RECORD] TRACK Part 3[TRACK] MIC INPUT Part 3[MIC INPUT] (CP5 only) Settings for All Parts 3[REVERB] Settings for All Performances 3[MASTER COMPRESSOR] 3[UTILITY] 3[FILE] Appendix