Yamaha RX-V1600 Owner's Manual - Page 95

Wake on RS-232C access, U.S.A. model only - remote codes

Get Yamaha RX-V1600 PDF manuals and user guides
UPC - 027108924229
View all Yamaha RX-V1600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

■ Remote sensor REMOTE SEN Use to activate or deactivate the signal-receiving capability of the remote control sensor on the front panel of this unit. Choices: ON, OFF • Select ON if you want to activate the signal-receiving capability of the remote control sensor. • Select OFF if you want to deactivate the signal- receiving capability of the remote control sensor. Note We recommend setting this parameter to ON in most cases. ■ Wake on RS-232C access WAKE ON 232C Use to set this unit to transmit data via the RS-232C interface when this unit is in the standby mode. Choices: Y (yes), N (no) • Select Y set this unit to transmit data via the RS-232C interface. • Select N set this unit not to transmit data via the RS-232C interface. ■ Remote control AMP ID REMOTE AMP Use to set the AMP ID of this unit for remote control recognition (see page 95). Choices: ID1, ID2 • Select ID1 when the remote control AMP library code is set to 2001. • Select ID2 when the remote control AMP library code is set to 2002. Note You need to set the corresponding remote control code for the remote control. ■ Remote control tuner ID REMOTE TUN Use to set the tuner ID of this unit for remote control recognition (see page 95). Choices: ID1, ID2 • Select ID1 when the remote control tuner library code is set to 2602. • Select ID2 when the remote control tuner library code is set to 2603. Note You need to set the corresponding remote control code for the remote control. ADVANCED SETUP ■ Remote control XM ID REMOTE XM (U.S.A. model only) Use to switch the XM-related remote control codes between ID1 and ID2. Choices: ID1, ID2 • Select ID1 when the remote control XM library code is set to 2604. • Select ID2 when the remote control XM library code is set to 2605. Note You need to set the corresponding remote control code for the remote control. ■ Fan operation mode FAN MODE Use to set the operation of the cooling fan of this unit. Choices: AUTO, CONT. • Select AUTO to set the fan to operate automatically according to the temperature of this unit. • Select CONT. to set the fan to operate continuously regardless of the temperature of this unit. ■ Tuner frequency step TU (Asia and General models only) Use to set the tuner frequency step according to the frequency spacing in your area. Choices: AM10/FM100, AM9/FM50 • Select AM10/FM100 for North, Central and South America. • Select AM9/FM50 for all other areas. ■ Bi-AMP BI-AMP Use to activate or deactivate the bi-AMP function. Choices: ON, OFF • Select ON if you want to activate the bi-AMP function. • Select OFF if you want to deactivate the bi-AMP function. Note When BI-AMP is set to ON, the SURROUND BACK terminals cannot be used to connect surround back speakers in that the SURROUND BACK terminals are already used for the bi-AMP connection (see page 19). ■ Video reset V-RESET Use to initialize the parameter settings for DISPLAY SET in OPTION MENU (see page 85). This feature is useful if the SET MENU items are not displayed on your video monitor due to a technical error between the CMPNT I/P setting and the capability of your video monitor. That is, if your video monitor does not support the analog video signals with 480p of resolution, the SET MENU items may not be displayed on your video monitor when CMPNT I/P is set to ON (see page 85). Choices: YES, CANCEL Note The parameter setting for DIMMER is not initialized (see page 85). ADVANCED OPERATION 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
91
ADVANCED SETUP
ADVANCED
OPERATION
■
Remote sensor
REMOTE SEN
Use to activate or deactivate the signal-receiving
capability of the remote control sensor on the front panel
of this unit.
Choices:
ON
, OFF
•
Select ON if you want to activate the signal-receiving
capability of the remote control sensor.
•
Select OFF if you want to deactivate the signal-
receiving capability of the remote control sensor.
We recommend setting this parameter to ON in most cases.
■
Wake on RS-232C access
WAKE ON 232C
Use to set this unit to transmit data via the RS-232C
interface when this unit is in the standby mode.
Choices:
Y
(yes), N (no)
•
Select Y set this unit to transmit data via the RS-232C
interface.
•
Select N set this unit not to transmit data via the
RS-232C interface.
■
Remote control AMP ID
REMOTE AMP
Use to set the AMP ID of this unit for remote control
recognition (see page 95).
Choices:
ID1
, ID2
•
Select ID1 when the remote control AMP library code
is set to 2001.
•
Select ID2 when the remote control AMP library code
is set to 2002.
You need to set the corresponding remote control code for the
remote control.
■
Remote control tuner ID
REMOTE TUN
Use to set the tuner ID of this unit for remote control
recognition (see page 95).
Choices:
ID1
, ID2
•
Select ID1 when the remote control tuner library code
is set to 2602.
•
Select ID2 when the remote control tuner library code
is set to 2603.
You need to set the corresponding remote control code for the
remote control.
■
Remote control XM ID
REMOTE XM
(U.S.A. model only)
Use to switch the XM-related remote control codes
between ID1 and ID2.
Choices:
ID1
, ID2
•
Select ID1 when the remote control XM library code is
set to 2604.
•
Select ID2 when the remote control XM library code is
set to 2605.
You need to set the corresponding remote control code for the
remote control.
■
Fan operation mode
FAN MODE
Use to set the operation of the cooling fan of this unit.
Choices:
AUTO
, CONT.
•
Select AUTO to set the fan to operate automatically
according to the temperature of this unit.
•
Select CONT. to set the fan to operate continuously
regardless of the temperature of this unit.
■
Tuner frequency step
TU
(Asia and General models only)
Use to set the tuner frequency step according to the
frequency spacing in your area.
Choices: AM10/FM100,
AM9/FM50
•
Select AM10/FM100 for North, Central and South
America.
•
Select AM9/FM50 for all other areas.
■
Bi-AMP
BI-AMP
Use to activate or deactivate the bi-AMP function.
Choices: ON,
OFF
•
Select ON if you want to activate the bi-AMP function.
•
Select OFF if you want to deactivate the bi-AMP
function.
When BI-AMP is set to ON, the SURROUND BACK terminals
cannot be used to connect surround back speakers in that the
SURROUND BACK terminals are already used for the bi-AMP
connection (see page 19).
■
Video reset
V-RESET
Use to initialize the parameter settings for DISPLAY SET
in OPTION MENU (see page 85). This feature is useful if
the SET MENU items are not displayed on your video
monitor due to a technical error between the CMPNT I/P
setting and the capability of your video monitor. That is, if
your video monitor does not support the analog video
signals with 480p of resolution, the SET MENU items
may not be displayed on your video monitor when
CMPNT I/P is set to ON (see page 85).
Choices: YES,
CANCEL
The parameter setting for DIMMER is not initialized (see
page 85).
Note
Note
Note
Note
Note
Note