Bosch VIPX1 Operation Manual - Page 124

General malfunctions, Malfunction, Possible causes, Solution, Audio settings, Live configuration

Get Bosch VIPX1 PDF manuals and user guides View all Bosch VIPX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

EN | 124 Installation and Operating Manual | VIP X1 General malfunctions Malfunction Possible causes Solution No connection Incorrect cable connections. Check all cables, plugs, contacts, between the unit and terminals and connections. terminal program. The computer's serial inter- Check the other serial interface. face is not connected. Interface parameters do not match. If necessary select a different interface and make sure that the computer's interface parameters match those of the unit. Try the following standard parameters: 19,200 baud, 8 data bits, no parity, 1 stop bit. Next, disconnect the unit from the power supply and reconnect it again after a few seconds. No image transmission to remote station. Camera error. Faulty cable connections. Connect local monitor to the camera and check the camera function. Check all cables, plugs, contacts and connections. No connection estab- The unit's configuration. lished, no image transmission. Faulty installation. Check all configuration parameters. Check all cables, plugs, contacts and connections. Wrong IP address. Check the IP addresses (terminal program). Faulty data transmission within the LAN. Check the data transmission with ping. The maximum number of connections has been reached. Wait until there is a free connection and then call the sender again. No audio transmission to remote station. Hardware fault. Faulty cable connections. Check that all connected audio units are operating correctly. Check all cables, plugs, contacts and connections. Incorrect configuration. Check the audio parameters on the Audio settings and Livepage configuration configuration pages. The audio voice connection Wait until the connection is free is already in use by another and then call the sender again. receiver. Appendix Bosch Security Systems | 2006-12 | V2.5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
EN
|
124
Installation and Operating Manual |
VIP X1
Appendix
Bosch Security Systems | 2006-12 | V2.5
General malfunctions
Malfunction
Possible causes
Solution
No connection
between the unit and
terminal program.
Incorrect cable connections.
Check all cables, plugs, contacts,
terminals and connections.
The computer's serial inter-
face is not connected.
Check the other serial interface.
Interface parameters do not
match.
If necessary select a different inter-
face and make sure that the com-
puter's interface parameters match
those of the unit. Try the following
standard parameters:
19,200 baud, 8 data bits, no parity,
1 stop bit. Next, disconnect the unit
from the power supply and recon-
nect it again after a few seconds.
No image transmis-
sion to remote sta-
tion.
Camera error.
Connect local monitor to the cam-
era and check the camera function.
Faulty cable connections.
Check all cables, plugs, contacts
and connections.
No connection estab-
lished, no image
transmission.
The unit's configuration.
Check all configuration parame-
ters.
Faulty installation.
Check all cables, plugs, contacts
and connections.
Wrong IP address.
Check the IP addresses
(terminal program).
Faulty data transmission
within the LAN.
Check the data transmission with
ping
.
The maximum number of
connections has been
reached.
Wait until there is a free connection
and then call the sender again.
No audio transmis-
sion to remote sta-
tion.
Hardware fault.
Check that all connected audio
units are operating correctly.
Faulty cable connections.
Check all cables, plugs, contacts
and connections.
Incorrect configuration.
Check the audio parameters on the
Audio settings
and
Livepage
configuration
configuration
pages.
The audio voice connection
is already in use by another
receiver.
Wait until the connection is free
and then call the sender again.