Home » Brother International Manuals » Sewing Machines » Brother International BAS-326G PS » Manual Viewer

Brother International BAS-326G PS Instruction Manual - English - Page 21

INSTALLATION, <Power supply motor P.C. board&gt, <PMD P.C. board&gt, PMD P.C. board

Get Brother International BAS-326G PS PDF manuals and user guides

View all Brother International BAS-326G PS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. INSTALLATION Press the tab. 1843B Connector Machine head memory 7-pin Upper shaft motor 3-pin Synchronizer 14-pin Connector Work clamp pulse motor 4-pin black Thread trimmer solenoid 6-pin Tension release solenoid 4-pin Y pulse motor 4-pin blue X pulse motor 4-pin white NOTE: Route the X, Y and work clamp pulse motor harnesses so that they do not touch the PMD P.C. *1 : Be sure to make the ground connection. (Refer to "3-9. Connecting the ground wire".) Connection location on power supply motor P.C. board P3 (HEAD-M) P4 (UVW) P5 (SYNC) Connection location on PMD P.C. board P3 (PPM) P6 (SOL1) P7 (SOL2) P8 (YPM) P10 (XPM) Cord clamp/cable tie (4) (5) (5), (6) Cable tie (5), (6) (5), (6) (5), (6) (5), (6) (5), (6) (Continued on next page) BAS-326G PS 12

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
[1] Safety indications and their meanings	3
[2] Notes on safety	4
[3] Warning labels	6
CONTENTS	8
1. NAMES OF MAJOR PARTS	10
2. SPECIFICATIONS	11
3. INSTALLATION	12
3-1. Table processing diagram	12
3-2. Installing the control box	13
3-3. Installing the oil pan	13
3-4. Installing the machine head	14
3-5. Tilting the sewing machine head	18
3-6. Installing the operation panel	18
3-7. Installing the pneumatic unit	19
3-8. Connecting the cords	20
3-9. Connecting the ground wire	22
3-10. Connecting the power cord	23
3-11. Installing the cotton stand	23
3-12. Installing the eye guard	24
3-13. Installing the motor cover	25
3-14. Lubrication	26
3-15. Installing the machine head fixing bolt	27
4. PREPARATION BEFORE SEWING	28
4-1. Installing the needle	28
4-2. Threading the upper thread	28
4-3. Foot switch operating method	29
4-4. Winding the lower thread	30
4-5. Installing the bobbin case	31
4-6. Thread tension	32
4-6-1. Lower thread tension	32
4-6-2. Upper thread tension	32
4-7. Home position detection	33
5. USING THE OPERATION PANEL(BASIC OPERATIONS)	34
5-1. Name and function of each operation panel item	34
5-2. Loading sewing data	36
5-3. Setting the program number	36
5-4. Setting the X-scale and Y-scale	37
5-5. Setting the sewing speed	37
5-6. Checking the sewing pattern	38
5-7. Setting the height of the intermittent presser foot	39
6. USING THE OPERATION PANEL(ADVANCED OPERATIONS)	40
6-1. List of advanced functions	40
6-2. Setting memory switches	41
6-3. List of memory switch settings	42
6-4. Using the lower thread counter	43
6-5. Using the production counter	44
6-6. Setting the split number	45
6-7. Using user programs	46
6-8. Using cycle programs	49
6-9. Direct selection (combination table)	51
6-10. X and Y parallel movement of sewing pattern	52
6-11. Clearing memory data (reinitialization)	53
7. USING CF CARDS	54
7-1. Notes on handling CF cards (sold separately)	54
7-2. Structure of a CF card folder	54
7-3. Data read/write mode	55
7-3-1. Reading all sewing data from the CF card at once	56
7-3-2. Writing all sewing data to the CF card at once	57
8. SEWING	58
8-1. Sewing	58
8-2. Using the STOP switch	59
8-3. Using the thread wiper switch	59
9. CLEANING	60
9-1. Cleaning the rotary hook	60
9-2. Cleaning the control box air inlet ports	60
9-3. Draining the oil	61
9-4. Cleaning the eye guard	61
9-5. Checking the needle	61
9-6. Lubrication	61
10. STANDARD ADJUSTMENTS	62
10-1. Checking the machine head switch	62
10-2. Arm thread guide R	62
10-3. Thread take-up spring	63
10-4. Adjusting the needle bar height	63
10-5. Adjusting the needle bar lift amount	64
10-6. Adjusting the needle guard	64
10-7. Adjusting the needle clearance	65
10-8. Adjusting the inner rotary hook and hook stopper overlap	65
10-9. Rotary hook lubrication amount	65
10-10. Adjusting the position of the movable knife	66
10-11. Replacing the movable and fixed knives	68
10-11-1. Installing the feed plate	69
10-12. Adjusting the thread wiper	70
10-13. Intermittent presser foot installation position	70
10-14. Changing the intermittent stroke	71
10-15. Adjusting the work clamp lift amount	73
10-16. Adjusting the air pressure	73
11. TABLE OF ERROR CODES	74
12. TROUBLESHOOTING	78
13. 7-SEGMENT DISPLAY	82