Home » Brother International Manuals » Sewing Machines » Brother International BAS-326G PS » Manual Viewer

Brother International BAS-326G PS Instruction Manual - English - Page 73

Adjusting the work clamp lift amount, 10-16. Adjusting the air pressure, downward to lock it.

Get Brother International BAS-326G PS PDF manuals and user guides

View all Brother International BAS-326G PS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

10. STANDARD ADJUSTMENTS 10-15. Adjusting the work clamp lift amount The maximum lift amount for the work clamp is 30 mm above the top of the needle plate. Max. 30mm 5018Q 2165B 1. Turn on the air, and depress the work clamp switch (1) to raise the work clamp (2). 2. Loosen the two bolts (4) of the work clamp arm lever (3), and move the work clamp arm lever (3) up or down to adjust. 10-16. Adjusting the air pressure Lift up the handle (2) of the regulator (1) and then turn it to adjust the air pressure to 0.5 MPa. After adjustment is complete, push the handle (2) downward to lock it. If water has collected in the bottle of the regulator (1), turn the drain cock (3) in the direction indicated by an arrow to drain the water. NOTE: Open the air cock (4) slowly. 1912B BAS-326G PS 64

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
[1] Safety indications and their meanings	3
[2] Notes on safety	4
[3] Warning labels	6
CONTENTS	8
1. NAMES OF MAJOR PARTS	10
2. SPECIFICATIONS	11
3. INSTALLATION	12
3-1. Table processing diagram	12
3-2. Installing the control box	13
3-3. Installing the oil pan	13
3-4. Installing the machine head	14
3-5. Tilting the sewing machine head	18
3-6. Installing the operation panel	18
3-7. Installing the pneumatic unit	19
3-8. Connecting the cords	20
3-9. Connecting the ground wire	22
3-10. Connecting the power cord	23
3-11. Installing the cotton stand	23
3-12. Installing the eye guard	24
3-13. Installing the motor cover	25
3-14. Lubrication	26
3-15. Installing the machine head fixing bolt	27
4. PREPARATION BEFORE SEWING	28
4-1. Installing the needle	28
4-2. Threading the upper thread	28
4-3. Foot switch operating method	29
4-4. Winding the lower thread	30
4-5. Installing the bobbin case	31
4-6. Thread tension	32
4-6-1. Lower thread tension	32
4-6-2. Upper thread tension	32
4-7. Home position detection	33
5. USING THE OPERATION PANEL(BASIC OPERATIONS)	34
5-1. Name and function of each operation panel item	34
5-2. Loading sewing data	36
5-3. Setting the program number	36
5-4. Setting the X-scale and Y-scale	37
5-5. Setting the sewing speed	37
5-6. Checking the sewing pattern	38
5-7. Setting the height of the intermittent presser foot	39
6. USING THE OPERATION PANEL(ADVANCED OPERATIONS)	40
6-1. List of advanced functions	40
6-2. Setting memory switches	41
6-3. List of memory switch settings	42
6-4. Using the lower thread counter	43
6-5. Using the production counter	44
6-6. Setting the split number	45
6-7. Using user programs	46
6-8. Using cycle programs	49
6-9. Direct selection (combination table)	51
6-10. X and Y parallel movement of sewing pattern	52
6-11. Clearing memory data (reinitialization)	53
7. USING CF CARDS	54
7-1. Notes on handling CF cards (sold separately)	54
7-2. Structure of a CF card folder	54
7-3. Data read/write mode	55
7-3-1. Reading all sewing data from the CF card at once	56
7-3-2. Writing all sewing data to the CF card at once	57
8. SEWING	58
8-1. Sewing	58
8-2. Using the STOP switch	59
8-3. Using the thread wiper switch	59
9. CLEANING	60
9-1. Cleaning the rotary hook	60
9-2. Cleaning the control box air inlet ports	60
9-3. Draining the oil	61
9-4. Cleaning the eye guard	61
9-5. Checking the needle	61
9-6. Lubrication	61
10. STANDARD ADJUSTMENTS	62
10-1. Checking the machine head switch	62
10-2. Arm thread guide R	62
10-3. Thread take-up spring	63
10-4. Adjusting the needle bar height	63
10-5. Adjusting the needle bar lift amount	64
10-6. Adjusting the needle guard	64
10-7. Adjusting the needle clearance	65
10-8. Adjusting the inner rotary hook and hook stopper overlap	65
10-9. Rotary hook lubrication amount	65
10-10. Adjusting the position of the movable knife	66
10-11. Replacing the movable and fixed knives	68
10-11-1. Installing the feed plate	69
10-12. Adjusting the thread wiper	70
10-13. Intermittent presser foot installation position	70
10-14. Changing the intermittent stroke	71
10-15. Adjusting the work clamp lift amount	73
10-16. Adjusting the air pressure	73
11. TABLE OF ERROR CODES	74
12. TROUBLESHOOTING	78
13. 7-SEGMENT DISPLAY	82