Brother International FB-N310 Instruction Manual - English and Spanish - Page 43
Adjusting the under looper, movable needle guard and needle guard F, Einstellen des unteren Greifers
View all Brother International FB-N310 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 43 highlights
5. STANDARD ADJUSTMENTS 5. STANDARDEINSTELLUNGEN 5. RÉGLAGES STANDARD 5. AJUSTES ESTANDARES 5-2. Adjusting the under looper, movable needle guard and needle guard F 5-2. Einstellen des unteren Greifers, des einstellbaren Nadelschutzes und des Nadelschutzes F 0 - 0.05 mm 0 - 0,05 mm 3.8 mm (3.5 mm) 3,8 mm (3,5 mm) q q w 0 - 0.05 mm 0 - 0,05 mm Contact Berührung y t q r Fine thread (#50 or lower) 0.05 - 0.2 mm Thick thread (#30 or more) 0.2 - 0.3 mm e Feiner Faden (#50 oder weniger) 0,05 - 0,2 mm Dicker Faden (#30 oder mehr) 0,2 - 0,3 mm 0701Q 0702Q 0703Q 1. Turn the machine pulley to move the under looper q to the far left position. 2. Loosen the bolt w and adjust the distance between the under looper q tip and the needle center to 3.8 mm (When sewing mock safety stitches, you can adjust the distance to 3.5 mm for extra-high lift.). 3. Raise the needle from the down position, and when the under looper q tip and the needle center are aligned, adjust the under looper q so that it contacts the needle by 0 - 0.05 mm. 1. Raise the needle from the down position, and align the under looper q tip with the center of the needle. 2. Loosen the bolt e and move the movable needle guard r to adjust the gap between the needle and the under looper q to 0 - 0.05 mm. Raise the needle from the down position, and when the under looper q tip and the needle center are aligned, loosen the screw t and adjust the gap between the needle guard F y and the needle to 0.05 - 0.2 mm (for fine thread of #50 or lower) or 0.2 - 0.3 mm (for thick thread of #30 or more). 1. Den unteren Greifer q durch Drehen der Riemenscheibe ganz nach links zu stellen. 2. Die Schraube w lösen und den Abstand zwischen der Greiferspitze q und der Nadelmitte auf 3,8 mm einstellen (Beim Nähen von falschen Sicherheitsstichen läßt sich der Abstand für eine extragroßen Hub auf 3,5 mm einstellen.). 3. Die Nadel anheben und wenn die Spitze des unteren Greifers q auf die Nadelmitte ausgerichtet ist, den unteren Greifer w so einstellen, daß der Abstand zur Nadel 0 bis 0,05 mm beträgt. 1. Die Nadel anheben und die Spitze des unteren Greifers q auf die Nadelmitte ausrichten. 2. Die Schraube e lösen und den Nadelschutz r verschieben, um den Abstand zwischen der Nadel und dem unteren Greifer q auf 0 bis 0,05 mm einzustellen. Heben Sie die Nadel von der ganz abgesenkten Position an, bis die untere Greiferspitze q auf die Nadel ausgerichtet ist. Lösen Sie die Schraube t, um den Abstand zwischen dem Nadelschutz F y und der Nadel auf 0,05 - 0,2 mm für feines Garn (von #50 oder weniger), bzw. auf 0,2 - 0,3 mm für dickes Garn (von #30 oder mehr) einzustellen. 26 FB-N110, N210, N310