Canon GL1 GL1 Instruction Manual - Page 20

Protecting tapes from accidental erasure, Handling cassettes, Cassette memory

Page 20 highlights

Protecting tapes from accidental erasure E REC SAVE REC SAVE Quick Overview To protect your recording from accidental erasure, slide the tab on the cassette so that it exposes the hole and the red mark. (This switch position is usually labeled SAVE or ERASE OFF.) If you load this cassette and put the camera in record pause mode (p. 21), "THE TAPE IS SET FOR ERASURE PREVENTION" is displayed for approx. 4 seconds and then the v mark flashes in the display. The camera also shows the above phrase if you accidentally press the 2 (record) button with the camera switched to VCR mode. If you want to record on the cassette again, slide the tab back so the hole is closed. Handling cassettes • To protect the tape heads, transfer cassettes directly from the tape case to the camcorder - do not open the tape protect cover or touch the tape itself. • Do not use cassettes where the tape has been damaged or spliced - they may damage the camcorder. • Do not insert anything into the small holes on the cassette or cover them with cellophane tape. • Handle cassettes with care - dropping them or exposing them to external shocks may cause internal damage. • Store cassettes in the provided case, rewinding them to the start of the tape first, and then storing them upright. • A cassette with metal plated terminals may become dirty with use, affecting information transfer. Therefore, after using a tape around ten times, be sure to clean the terminals with a cotton swab. Cassette memory You are unable to use the cassette memory function with this camcorder. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104

20
E
Quick Overview
Protecting tapes from accidental erasure
Handling cassettes
Cassette memory
SAVE
REC
SAVE
REC
To protect your recording from accidental erasure, slide the tab on the cassette so that it exposes the hole
and the red mark. (This switch position is usually labeled SAVE or ERASE OFF.)
If you load this cassette and put the camera in record pause mode (p. 21), “THE TAPE IS SET FOR
ERASURE PREVENTION” is displayed for approx. 4 seconds and then the
v
mark flashes in the
display. The camera also shows the above phrase if you accidentally press the
2
(record) button with the
camera switched to VCR mode.
If you want to record on the cassette again, slide the tab back so the hole is closed.
To protect the tape heads, transfer cassettes directly from the tape case to the camcorder — do not open
the tape protect cover or touch the tape itself.
Do not use cassettes where the tape has been damaged or spliced — they may damage the camcorder.
Do not insert anything into the small holes on the cassette or cover them with cellophane tape.
Handle cassettes with care — dropping them or exposing them to external shocks may cause internal
damage.
Store cassettes in the provided case, rewinding them to the start of the tape first, and then storing them
upright.
A cassette with metal plated terminals may become dirty with use, affecting information transfer.
Therefore, after using a tape around ten times, be sure to clean the terminals with a cotton swab.
You are unable to use the cassette memory function with this camcorder.