Canon XC10 User Manual - Page 148

Set the DNS server's IP address in the camcorder., If you are using a wireless gateway router

Get Canon XC10 PDF manuals and user guides View all Canon XC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Troubleshooting 148 No access points found - The access point set in the camcorder could not be found. - Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using the camcorder in a location farther away from such appliances. - Make sure that you use the access point's SSID for the camcorder's Wi-Fi settings (A 119). - If the access point is using MAC address filtering, enter the camcorder's MAC address in the access point's configuration screen. Unable to access configuration files - Turn off the camcorder. After a short while, turn it on again. If the problem persists contact a Canon Service Center. Unable to complete WPS. - Turn off the camcorder and access point (wireless router). After a short while, turn them on again and try again. If the problem persists, perform setup using the [Search for Access Points] option (A 120). Unable to complete WPS. Try the operation again. - Some access points require pressing and holding the Wi-Fi Protected Setup (WPS) button. For details, refer to the instruction manual of your access point. - Make sure to touch [OK] on the camcorder's screen within 2 minutes of activating the Wi-Fi Protected Setup signal on the access point, whether by pressing the button or by entering the PIN code. Unable to connect - Could not connect to the access point or network device selected. - Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using the camcorder in a location farther away from such appliances. Unable to obtain an IP address - If you are not using a DHCP server, connect using the [Manual Setup] option and enter the IP address using the [Manual] option (A 122). - Turn on the DHCP server. If it is already on, make sure it is functioning properly. - Turn on the DNS server. If it is already on, make sure it is functioning properly. - Make sure the address range for the DHCP server is sufficient. - If you are not using a DNS server, set the DNS address to [0.0.0.0]. - Set the DNS server's IP address in the camcorder. - Turn on the DNS server. If it is already on, make sure it is functioning properly. - Make sure that the DNS server's IP address and the name for that address are correctly configured. - If you are using a wireless gateway router, make sure all of the devices in the network, including the camcorder, are configured with the correct gateway address. Wi-Fi authentication unsuccessful - Make sure the camcorder and access point are using the same authentication/encryption method and encryption key. - If the access point is using MAC address filtering, enter the camcorder's MAC address in the access point's configuration screen. Wi-Fi connection terminated - Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using the camcorder in a location farther away from such appliances. - The camcorder may not be able to connect to the access point if too many devices are accessing it. After a short while, establish the connection again. Wi-Fi error. Incorrect authentication method. - Make sure the camcorder and access point are correctly configured. - Make sure the camcorder and access point are using the same authentication/encryption method and encryption key. - If the access point is using MAC address filtering, enter the camcorder's MAC address in the access point's configuration screen. Wi-Fi error. Incorrect encryption key. - The encryption key (password) is case sensitive so make sure to enter it correctly. Wi-Fi error. Incorrect encryption method. - Make sure the camcorder and access point are using the same authentication/encryption method. - If the access point is using MAC address filtering, enter the camcorder's MAC address in the access point's configuration screen. Wi-Fi functions are not available in this index screen. - The Wi-Fi function cannot be activated from a clip playback index screen. Activate the function from the photo playback index screen. Table of Contents Menus Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Troubleshooting
148
Menus
Table of Contents
Index
No access points found
- The access point set in the camcorder could not be found.
- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using
the camcorder in a location farther away from such appliances.
- Make sure that you use the access point’s SSID for the camcorder’s Wi-Fi settings (
A
119).
- If the access point is using MAC address filtering, enter the camcorder's MAC address in the access point's
configuration screen.
Unable to access configuration files
- Turn off the camcorder. After a short while, turn it on again. If the problem persists contact a Canon Service Center.
Unable to complete WPS.
- Turn off the camcorder and access point (wireless router). After a short while, turn them on again and try again. If the
problem persists, perform setup using the [Search for Access Points] option (
A
120).
Unable to complete WPS. Try the operation again.
- Some access points require pressing and holding the Wi-Fi Protected Setup (WPS) button. For details, refer to the
instruction manual of your access point.
- Make sure to touch [OK] on the camcorder’s screen within 2 minutes of activating the Wi-Fi Protected Setup signal on
the access point, whether by pressing the button or by entering the PIN code.
Unable to connect
- Could not connect to the access point or network device selected.
- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using
the camcorder in a location farther away from such appliances.
Unable to obtain an IP address
- If you are not using a DHCP server, connect using the [Manual Setup] option and enter the IP address using the
[Manual] option (
A
122).
- Turn on the DHCP server. If it is already on, make sure it is functioning properly.
- Turn on the DNS server. If it is already on, make sure it is functioning properly.
- Make sure the address range for the DHCP server is sufficient.
- If you are not using a DNS server, set the DNS address to [0.0.0.0].
- Set the DNS server’s IP address in the camcorder.
- Turn on the DNS server. If it is already on, make sure it is functioning properly.
- Make sure that the DNS server’s IP address and the name for that address are correctly configured.
- If you are using a wireless gateway router, make sure all of the devices in the network, including the camcorder, are
configured with the correct gateway address.
Wi-Fi authentication unsuccessful
- Make sure the camcorder and access point are using the same authentication/encryption method and encryption key.
- If the access point is using MAC address filtering, enter the camcorder’s MAC address in the access point’s
configuration screen.
Wi-Fi connection terminated
- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using
the camcorder in a location farther away from such appliances.
- The camcorder may not be able to connect to the access point if too many devices are accessing it. After a short
while, establish the connection again.
Wi-Fi error.
Incorrect authentication method.
- Make sure the camcorder and access point are correctly configured.
- Make sure the camcorder and access point are using the same authentication/encryption method and encryption key.
- If the access point is using MAC address filtering, enter the camcorder’s MAC address in the access point’s
configuration screen.
Wi-Fi error.
Incorrect encryption key.
- The encryption key (password) is case sensitive so make sure to enter it correctly.
Wi-Fi error.
Incorrect encryption method.
- Make sure the camcorder and access point are using the same authentication/encryption method.
- If the access point is using MAC address filtering, enter the camcorder’s MAC address in the access point’s
configuration screen.
Wi-Fi functions are not available in this index screen.
- The Wi-Fi function cannot be activated from a clip playback index screen. Activate the function from the photo
playback index screen.