Compaq ProLiant 6400R Compaq Parallel Database Cluster Model PDC/05000 for Ora - Page 119

Start, Program, Command Console, CLI Window., Serial, Connect, Enter

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Installation and Configuration 5-23 To set port topologies and Arbitrated Loop Physical Address (ALPA) settings for both array controllers, perform these steps: NOTE: Refer to the Compaq StorageWorks documentation for more detailed information about changing the port topology settings. 1. Click on the Windows taskbar Start button. 2. Select Program, Command Console, CLI Window. 3. Click on the CLI window to display the Connection Selection dialog box. 4. Select Serial and click OK to display the Connect Serial dialog box. 5. Select the COM port to which the top array controller is connected. 6. Select a baud rate of 9600. 7. Click Connect to display the CLI window. 8. Press Enter to initialize communications. 9. Repeat steps 1 through 8 for the other COM port and the bottom array controller connection. 10. From the CLI window type the following and press Enter: set this node_id=xxxx-xxxx-xxxx-xxxx xx (xxxx-xxxx-xxxx-xxxx is the bar-coded World Wide ID located in the controller enclosure. The final xx is the two-digit checksum on the same label.) NOTE: The "other" controller will shut down and must be manually restarted by momentarily pressing the reset button on the controller's front panel. Wait for two minutes for the controller to boot before proceeding. 11. Configure both array controllers for multibus failover mode. a. Type the following command and press Enter: set nofailover b. Type the following command and press Enter: set multibus_failover copy=this_controller c. Wait two minutes for the controllers to reset.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
Installation and Configuration
5-23
To set port topologies and Arbitrated Loop Physical Address (ALPA) settings
for both array controllers, perform these steps:
NOTE:
Refer to the Compaq StorageWorks documentation for more detailed information
about changing the port topology settings.
1.
Click on the Windows taskbar
Start
button.
2.
Select
Program
,
Command Console
,
CLI Window.
3.
Click on the CLI window
to display the Connection Selection dialog
box.
4.
Select
Serial
and click
OK
to display the Connect Serial
dialog box.
5.
Select the COM port to which the top array controller is connected.
6.
Select a baud rate of 9600.
7.
Click
Connect
to display the CLI window.
8.
Press
Enter
to initialize communications.
9.
Repeat steps 1 through 8 for the other COM port and the bottom array
controller connection.
10.
From the CLI window type the following and press
Enter:
set this node_id
=
xxxx-xxxx-xxxx-xxxx xx
(xxxx-xxxx-xxxx-xxxx
is the bar-coded World Wide ID located in the
controller enclosure. The final xx is the two-digit checksum on the same
label.)
NOTE:
The
“
other
”
controller will shut down and must be manually restarted by
momentarily pressing the reset button on the controller
’
s front panel. Wait for two
minutes for the controller to boot before proceeding.
11.
Configure both array controllers for multibus failover mode.
a.
Type the following command and press
Enter:
set nofailover
b.
Type the following command and press
Enter:
set multibus_failover copy=this_controller
c.
Wait two minutes for the controllers to reset.