Dell OptiPlex 755 Administration Guide - Page 9
Set PID and PPS
View all Dell OptiPlex 755 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
The menu contains the parameters for the setup and configuration server. This menu also contains the security settings for PSK and PKI configurations. l Current Provisioning Mode - Displays the current provisioning TLS Mode: None, PKI, or PSK. This configuration is only shown in Enterprise Provision Model. l Provisioning Record - Displays the provision PSK/PKI record data of the computer. If the data has not been entered, the MEBx displays a message that states: Provision Record not present If the data is entered, the Provision Record displays the following: ¡ TLS provisioning mode - Displays the current configuration mode of the computer: None, PSK or PKI. ¡ Provisioning IP - The IP of the setup and configuration server. ¡ Date of Provision - Displays the date and time of the provisioning in the format MM/DD/YYYY at HH:MM. ¡ DNS - Displays if Secure DNS is being used or not. 0 indicates DNS is not in use, 1 indicates secure DNS is being used (PKI only). ¡ Host Initiated - Displays if the setup and configuration process was initiated by the host: 'No' indicates the setup and configuration process was not host initiated; 'Yes' indicates the setup and configuration process was host initiated (PKI only). ¡ Hash Data - Displays the 40 character certificate hash data (PKI only). ¡ Hash Algorithm - Describes the hash type. Currently only SHA1 is supported (PKI only). ¡ IsDefault - Displays 'Yes' if the Hash algorithm is the default algorithm selected. Displays 'No' if the hash algorithm is not the default algorithm used (PKI only). ¡ FQDN - FQDN of the provisioning server mentioned in certificate (PKI only). ¡ Serial Number - The 32 character that indicate the Certificate Authority serial numbers. ¡ Time Validity Pass - Indicates whether the certificate passed the time validity check. l Provisioning Server - The IP address and port number (0 - 65535) for an Intel AMT provisioning server. This configuration is only shown for the enterprise provision model. The default port number is 9971. l TLS PSK - Contains the settings for TLS PSK configuration settings. ¡ Set PID and PPS - Sets the provisioning identifier (PID) and provisioning passphrase (PPS). Enter the PID and PPS in the dash format. (Ex. PID: 1234-ABCD ; PPS: 1234-ABCD-1234-ABCD-1234-ABCD-1234-ABCD) NOTE - A PPS value of ' '0000-0000-0000-0000-0000-0000-0000-0000' does not change the setup configuration state. If this value is used the setup and configuration state stays as 'Not-started'. ¡ Delete PID and PPS - Deletes the current PID and PPS stored in ME. If there is no PID and PPS entered, the MEBX returns an error message. Note: Using this option does NOT set the setup and configuration process parameter to "Not Started." This option sets the setup and configuration process parameter to "In Process." ¡ Time Validity Pass - Indicates whether the certificate passed the time validity check. l TLS PKI - Contains the settings for the TLS PKI configuration settings. ¡ Remote Configuration Enable/Disable - Disables or enables remote configuration. If this option is not enabled, remote configuration cannot occur. ¡ Manage Certificate Hashes - Displays the list of hashes that are currently stored and the current status. To change the active status of the certificate press the key. To delete the hash press the key. To add another key press the key. ¡ Set FQDN - Sets the fully qualified domain name for the computer. ¡ Set PKI DNS suffix - Sets the PKI DNS suffix. TLS PSK The submenu contains the settings for TLS PSK configuration settings. Setting or deleting the PID/PPS causes a partial un-provision if the setup and configuration is "In-process". l Set PID and PPS - Sets the PID and PPS. Enter the PID and PPS in the dash format. (Ex. PID: 1234-ABCD ; PPS: 1234-ABCD-1234-ABCD-1234-ABCD1234-ABCD) Note - A PPS value of '0000-0000-0000-0000-0000-0000-0000-0000' does not change the setup configuration state. If this value is used the setup and configuration state stays as "Not-started." l Delete PID and PPS - Deletes the current PID and PPS stored in ME. If there is no PID and PPS entered, the MEBX returns an error message.