Garmin GPSMAP 60CS Owner's Manual - Page 67

Interface Setup

Get Garmin GPSMAP 60CS - Hiking GPS Receiver PDF manuals and user guides
UPC - 753759044060
View all Garmin GPSMAP 60CS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

RTCM In - Provides DGPS input using a standard RTCM SC-104 format. No output. RTCM In/NMEA Out - Allows DGPS input using a standard RTCM SC-104 format and supports the output of standard NMEA 0183 version 3.01 data. RTCM In/Text Out - Allows DGPS input using a standard RTCM SC-104 format and supports the output of simple ASCII text output of location and velocity information None - Provides no interfacing capabilities. To change an Interface Setup feature: 1. Access the Interface Setup Page as explained at the beginning of this section. 2. Highlight the desired setting and press ENTER. 3. When you select Text Out and /or RTCM In, additional fields will appear. Use the ROCKER key to highlight "Baud Rate" and press ENTER. Use the ROCKER key to highlight the desired setting and press ENTER. 4. For Garmin DGPS or RTCM In/NMEA Out, use the ROCKER key to highlight "Beacon" and press ENTER. Use the ROCKER key to select "Scan" or "User" and press ENTER. If "Scan" is selected, the GPSmap 60CS will automatically direct the beacon receiver to scan for available beacon transmitters. If "User" is selected, then select the "Freq" and "Bit Rate" fields and enter the appropriate settings. The beacon status, signal-to-noise ratio and distance to beacon are displayed in the bottom of the page. GPSmap 60CS GPS Navigation Interface Setup Data Format Page for GARMIN DGPS Data Format Page for RTCM In/NMEA Out Data Format Page for: NMEA In/NMEA Out Text Out RTCM In RTCM In/Text Out IMPORTANT NOTE: When the USB cable is connected to the GPS map 60CS, it is automatically detected and communicates only in Garmin Format. When the USB is connected, Garmin format will not communicate through the Serial connection, while all other formats can be used by the Serial connection with the USB still connected. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
57
GPSmap 60CS
GPS Navigation
IMPORTANT NOTE:
When the USB cable is con-
nected to the GPS map 60CS,
it is automatically detected and
communicates only in Garmin
Format. When the USB is con-
nected, Garmin format will not
communicate through the Serial
connection, while all other
formats can be used by the
Serial connection with the USB
still connected.
RTCM In
- Provides DGPS input using a standard RTCM SC-104
format. No output.
RTCM In/NMEA Out
- Allows DGPS input using a standard RTCM
SC-104 format and supports the output of standard NMEA
0183 version 3.01 data.
RTCM In/Text Out
- Allows DGPS input using a standard RTCM
SC-104 format and supports the output of simple ASCII text output of
location and velocity information
None
- Provides no interfacing capabilities.
To change an Interface Setup feature:
1.
Access the Interface Setup Page as explained at the beginning
of this section.
2.
Highlight the desired setting and press
ENTER
.
3. When you select Text Out and /or RTCM In, additional fields will
appear. Use the
ROCKER
key to highlight “Baud Rate” and
press
ENTER
. Use the
ROCKER
key to highlight the desired
setting and press
ENTER
.
4. For Garmin DGPS or RTCM In/NMEA Out, use the
ROCKER
key
to highlight “Beacon” and press
ENTER
. Use the
ROCKER
key
to select “Scan” or “User” and press
ENTER
.
If “Scan” is selected, the GPSmap 60CS will automatically direct
the beacon receiver to scan for available beacon transmitters.
If “User” is selected,
then select the “Freq” and “Bit Rate” fields
and enter the appropriate settings. The beacon status, signal-to-noise
ratio and distance to beacon are displayed in the bottom of the page.
Interface Setup
Data Format Page for
GARMIN DGPS
Data Format Page for:
NMEA In/NMEA Out
Text Out
RTCM In
RTCM In/Text Out
Data Format Page for
RTCM In/NMEA Out