GE AZ61H12DAB Owners Manual - Page 4

Other features, Zoneline.

Get GE AZ61H12DAB PDF manuals and user guides View all GE AZ61H12DAB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Other features of your Zoneline. Ventilation Control NOTE:Two shipping screws must be removed from the vent door before use..Seethe Installation Instructions in the back of this manual. If you do not plan to use the ventilation feature, leave these two screws in place. The ventilation control lever is located at the middle left side of the Zoneline unit, behind the room cabinet. Open position l When set at the closed position, only the air inside the room is circulated and filtered. When set at the open position, some outdoor air will be drawn into the room. This will reduce the heating or cooling efficiency. Energy Tip: Keepthe vent control in the closed position. The room air will be filtered and circulated. Ventcontrol (shownin middleposition) Closed position To Remove the Room Cabinet Additional controls are located behind the room cabinet. To remove: Pullout at the bottom to releaseit from the tabs (1).Then lift up (2). To replace: Placethe tabs over the top rail (1).Push inward at the bottom until it snaps into place (2). Air Direction To change the air direction, remove the room cabinet. Removethe 7 louver screws that hold the louver insert in place. Flipthe louver insert 180° replace the screws and the room cabinet. Louverscrews Remove the room cabinet and flip the louver insert to change the air direction. 4 Louvesrcrews Default position

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Other features
of
your
Zoneline.
Ventilation
Control
NOTE:Two
shipping screws
must be removed
from
the vent door before use..Seethe Installation
Instructions in the back of this manual. If
you
do not
plan to use the ventilation feature, leave these two
screws
in place.
The ventilation control lever is located at
the middle left side of the Zoneline unit,
behind the room cabinet.
When set at the closed position, only the air
inside the room is circulated and filtered.
When set at the open position, some outdoor
air will be drawn into the room. This will reduce
the heating or cooling efficiency.
Energy Tip:
Keepthe vent control in the closed
position. The room air will be filtered and circulated.
Open
position
l
Ventcontrol
(shownin
middleposition)
Closed
position
To Remove the Room
Cabinet
Additional controls are located behind the
room cabinet.
To remove:
Pullout at the bottom to releaseit from
the tabs (1).Then lift up (2).
To replace:
Placethe tabs over the top rail (1).Push
inward at the bottom until it snaps into place (2).
Air Direction
To change the air direction, remove the room
cabinet. Removethe 7 louver screws that hold
the louver insert in place. Flipthe louver insert 180°
replace the screws and the room cabinet.
Louverscrews
Remove the room cabinet and flip the louver
insert to change the air direction.
Default
position
4
Louver
screws