HP AD510A HP StorageWorks 1500 Modular Smart Array maintenance and service gui - Page 53

Controller Disabled, Autoflash Started

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Message 151 BEACON OFF Type Informational 201 ARRAY CONTROLLER TEMPERATURE OK Informational 202 ARRAY CONTROLLER OVERHEATING Error 203 ARRAY CONTROLLER OVERHEATED Error 204 ARRAY Error CONTROLLER DISABLED 205 ARRAY CONTROLLER RESTARTING 300 RECOVERY ROM AUTOFLASH STARTED Informational Informational Description Action The LEDs on the MSA and all connected hard drives are no longer blinking because the host-based application is no longer identifying or configuring this MSA. The temperature sensor on the array controller indicates that the temperature that was previously exceeding the normal operating range is now back within the range. The temperature sensor on the array controller indicates that the array controller is starting to exceed the normal operating range. Check all MSA fans and ensure they are operating. Any failed fan should be replaced. Ensure that there is a module or blanking panel (cover plate) in all MSA chassis bays and slots. Empty bays affect the airflow and cooling ability of the MSA. The temperature sensor on the array controller indicates that the array controller has exceeded the safe operating range. The MSA should be powered off as soon as possible to avoid hardware failure. Check all MSA fans and ensure they are operating. Any failed fan should be replaced. Ensure that there is a module or blanking panel (cover plate) in all MSA chassis bays and slots. Empty bays affect the airflow and cooling ability of the MSA. The array controller has been disabled due to a redundancy failure. Remove the failed array controller, wait 10 seconds, and then reinsert the array controller, ensuring that it is fully seated in the chassis. Should the issue persist, contact HP support. The array controller has completed firmware cloning and will be restarted automatically. The array controller has detected that the firmware's backup recovery ROM image is invalid and is copying the current active firmware image into the backup recovery ROM. maintenance and service guide 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Message
Type
Description
Action
151 BEACON OFF
Informational
The LEDs on the MSA and
all connected hard drives
are no longer blinking
because the host-based
application is no longer
identifying or con
fi
guring
this MSA.
201 ARRAY
CONTROLLER
TEMPERATURE OK
Informational
The temperature sensor
on the array controller
indicates that the
temperature that was
previously exceeding the
normal operating range is
now back within the range.
202 ARRAY
CONTROLLER
OVERHEATING
Error
The temperature sensor
on the array controller
indicates that the array
controller is starting
to exceed the normal
operating range.
Check all MSA fans and
ensure they are operating.
Any failed fan should be
replaced. Ensure that there
is a module or blanking
panel (cover plate) in all
MSA chassis bays and slots.
Empty bays affect the air
fl
ow
and cooling ability of the
MSA.
203 ARRAY
CONTROLLER
OVERHEATED
Error
The temperature sensor
on the array controller
indicates that the array
controller has exceeded the
safe operating range.
The MSA should be powered
off as soon as possible to
avoid hardware failure.
Check all MSA fans and
ensure they are operating.
Any failed fan should be
replaced. Ensure that there
is a module or blanking
panel (cover plate) in all
MSA chassis bays and slots.
Empty bays affect the air
fl
ow
and cooling ability of the
MSA.
204 ARRAY
CONTROLLER DISABLED
Error
The array controller has
been disabled due to a
redundancy failure.
Remove the failed array
controller, wait 10 seconds,
and then reinsert the array
controller, ensuring that it is
fully seated in the chassis.
Should the issue persist,
contact HP support.
205 ARRAY
CONTROLLER
RESTARTING
Informational
The array controller has
completed
fi
rmware cloning
and will be restarted
automatically.
300 RECOVERY ROM
AUTOFLASH STARTED
Informational
The array controller has
detected that the
fi
rmware's
backup recovery ROM
image is invalid and is
copying the current active
fi
rmware image into the
backup recovery ROM.
maintenance and service guide
53