HP AD510A HP StorageWorks 1500 Modular Smart Array maintenance and service gui - Page 76

Installing the component, If you replace a hard drive while the system is off

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

• If you replace a hard drive while the system is off, it may be necessary to rebuild the replaced hard drive. 1. Review all warnings, cautions, and preparation procedures as detailed in Warnings and precautions. 2. Be sure that the Online and Drive Access LED LEDs are both Off and that the Fault LED is On. 3. Press the ejector button (1) and pull the release lever to the full open position (2). IMPORTANT: Wait approximately 10 seconds for the internal disk to stop spinning before pulling the hard drive out of the enclosure. Handling a hard drive while the internal media is spinning can damage the media. 4. Pull the hard drive out of the storage enclosure bay (3). 1 3 2 15598 Installing the component 1. Press the hard drive ejector button (1) and pull the release lever to the full open position (2). 1 2 15599 2. Slide the replacement hard drive into the same bay from which the old hard drive was just removed, making sure that the lever is in the full open position to ensure a correct latch. Then, push the hard drive into the bay as far as it will go, pressing firmly on the hard drive to make sure that it is seated properly (1). 76 Customer replaceable components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
•
If you replace a hard drive while the system is off, it may be necessary to rebuild the replaced
hard drive.
1.
Review all warnings, cautions, and preparation procedures as detailed in
Warnings and precautions
.
2.
Be sure that the Online and Drive Access LED LEDs are both Off and that the Fault LED is On.
3.
Press the ejector button (
1
) and pull the release lever to the full open position (
2
).
IMPORTANT:
Wait approximately 10 seconds for the internal disk to stop spinning before pulling the
hard drive out of the enclosure. Handling a hard drive while the internal media is spinning
can damage the media.
4.
Pull the hard drive out of the storage enclosure bay (
3
).
15598
3
2
1
Installing the component
1.
Press the hard drive ejector button (
1
) and pull the release lever to the full open position (
2
).
15599
1
2
2.
Slide the replacement hard drive into the same bay from which the old hard drive was just removed,
making sure that the lever is in the full open position to ensure a correct latch. Then, push the
hard drive into the bay as far as it will go, pressing
fi
rmly on the hard drive to make sure that it is
seated properly (
1
).
76
Customer replaceable components