HP BL680c HP ProLiant Firmware Maintenance CD User Guide - Page 7

Supported firmware

Get HP BL680c - ProLiant - G5 PDF manuals and user guides
UPC - 884420396314
View all HP BL680c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

o /report generates a target summary and how the components in the repository affect the target (For example, whether each component applies to the target or not.) o /inventory_report generates a report of the components in the specified repository. • Accepts command line parameters from an input file Supported firmware The Firmware Maintenance CD provides the means to update the following firmware. Firmware type Supported by HP Firmware Maintenance CD System ROM Yes iLO 2 firmware Yes, local and remote Broadcom NIC firmware Yes Intel NIC firmware No NetXen NIC firmware No Power PIC firmware Yes, beginning with Firmware Maintenance CD 8.60 Smart Array controller firmware Yes SAS and SATA hard drive firmware behind Smart Array controllers SAS and SATA hard drive firmware behind nonSmart Array controllers Emulex, QLogic, and Brocade Fibre Channel Host Bus Adapter firmware Tape blade firmware Yes No Yes, offline only Yes Onboard Administrator firmware Virtual Connect firmware* HP StorageWorks 600 Modular Disk System (MDS600 )** HP 3Gb SAS BL Switch firmware*** Yes, online only Yes, online only and components must be downloaded from the web and added to the CD Yes, offline only No *Virtual Connect firmware components are not shipped with the HP Firmware Maintenance CD because of their size (approximately 50 MB per component). However, if the Virtual Connect firmware components are downloaded from the HP website, they can be added to the Firmware Maintenance CD by creating a USB key using the USB Key Utility. The latest version can be obtained from the HP BladeSystem Firmware Maintenance website (http://www.hp.com/go/bladesystemupdates). **MDS600 firmware update requires HP Smart Update Manager 3.6.0 or later. All blades in an enclosure with Smart Array P700M controllers, except the blade doing the update, must be turned off before the firmware update process is initiated. MDS600 firmware can only be updated using the Firmware Maintenance CD in offline mode. Introduction 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Introduction 7
o
/report generates a target summary and how the components in the repository affect the target
(For example, whether each component applies to the target or not.)
o
/inventory_report generates a report of the components in the specified repository.
•
Accepts command line parameters from an input file
Supported firmware
The Firmware Maintenance CD provides the means to update the following firmware.
Firmware type
Supported by HP Firmware Maintenance CD
System ROM
Yes
iLO 2 firmware
Yes, local and remote
Broadcom NIC firmware
Yes
Intel NIC firmware
No
NetXen NIC firmware
No
Power PIC firmware
Yes, beginning with Firmware Maintenance CD 8.60
Smart Array controller firmware
Yes
SAS and SATA hard drive firmware behind Smart
Array controllers
Yes
SAS and SATA hard drive firmware behind non-
Smart Array controllers
No
Emulex, QLogic, and Brocade Fibre Channel Host
Bus Adapter firmware
Yes, offline only
Tape blade firmware
Yes
Onboard Administrator firmware
Yes, online only
Virtual Connect firmware*
Yes, online only and components must be downloaded
from the web and added to the CD
HP StorageWorks 600 Modular Disk System
(MDS600 )**
Yes, offline only
HP 3Gb SAS BL Switch firmware***
No
*Virtual Connect firmware components are not shipped with the HP Firmware Maintenance CD because
of their size (approximately 50 MB per component). However, if the Virtual Connect firmware
components are downloaded from the HP website, they can be added to the Firmware Maintenance CD
by creating a USB key using the USB Key Utility. The latest version can be obtained from the HP
BladeSystem Firmware Maintenance website (
).
**MDS600 firmware update requires HP Smart Update Manager 3.6.0 or later. All blades in an
enclosure with Smart Array P700M controllers, except the blade doing the update, must be turned off
before the firmware update process is initiated.
MDS600 firmware can only be updated using the
Firmware Maintenance CD in offline mode.