HP J3111A HP JetDirect 600N Print Server Hardware Installation Guide - 5969-68 - Page 29

To enable or disable network protocols, Control Panel, Configuration

Get HP J3111A - JetDirect 600N Network Card PDF manuals and user guides
UPC - 002421211157
View all HP J3111A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

G eliminate unnecessary information on the JetDirect Configuration Page, which displays status information for all enabled protocols. G display protocol-specific error conditions on the printer's control panel. These warning messages are displayed only if all enabled protocols are unable to print. To enable or disable network protocols 1. Take the printer offline by pressing [Go]. The "Ready" LED should be off. 2. Press [Menu] repeatedly until EIO # JETDIRECT MENU is displayed (# identifies the EIO slot number of the card). 3. Press [Item] until CFG NETWORK=NO* appears. NO* indicates that access to the EIO JetDirect network menus will be bypassed. You must change this to CFG NETWORK=YES* to access the EIO JetDirect menus: a. Press [Value]. CFG NETWORK=YES appears. b. Press [Select]. CFG NETWORK=YES* appears. 4. Press [Item] to scroll through each network protocol until the one you want to change is displayed. IPX/SPX=ON* DLC/LLC=ON* TCP/IP=ON* G To change the protocol status, press [Value] and then press [Select]. G Press [Item] to continue to the next protocol. ETALK=ON* Note: ON* indicates the protocol is enabled. OFF* indicates the protocol is disabled. "ETALK" refers to the EtherTalk protocol (not available on Token Ring cards) 5. To activate the printer and save your changes, press [Go]. Control Panel 3 Configuration Control Panel Configuration 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Control Panel Configuration 3-3
Control Panel
Configuration
3
●
eliminate unnecessary information on the JetDirect
Configuration Page, which displays status information
for all enabled protocols.
●
display protocol-specific error conditions on the printer
’
s control
panel. These warning messages are displayed only if all enabled
protocols are unable to print.
To enable or disable network protocols
1.
Take the printer offline by pressing
[Go]
. The
“
Ready
”
LED
should be off.
2.
Press
[Menu]
repeatedly until
EIO # JETDIRECT MENU
is displayed
(# identifies the EIO slot number of the card).
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
NO*
indicates that access to the EIO JetDirect network menus
will be bypassed. You must change this to
CFG NETWORK=YES*
to
access the EIO JetDirect menus:
a.
Press
[Value]
.
CFG NETWORK=YES
appears.
b.
Press
[Select]
.
CFG NETWORK=YES*
appears.
4.
Press
[Item]
to scroll through each network protocol until the one
you want to change is displayed.
5.
To activate the printer and save your changes, press
[Go]
.
IPX/SPX=ON*
●
To change the protocol status, press
[Value]
and then press
[Select]
.
●
Press
[Item]
to continue to the next protocol.
DLC/LLC=ON*
TCP/IP=ON*
ETALK=ON*
Note:
ON* indicates the protocol is enabled.
OFF* indicates the protocol is disabled.
“
ETALK
”
refers to the EtherTalk protocol (not available on Token Ring
cards)