HP J3111A HP JetDirect 600N Print Server Hardware Installation Guide - 5969-68 - Page 41

Viewing the Embedded Web Server

Get HP J3111A - JetDirect 600N Network Card PDF manuals and user guides
UPC - 002421211157
View all HP J3111A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Viewing the Embedded Web Server Before you can use the embedded web server, the HP JetDirect print server must be configured with an IP address. There are many ways to configure an IP address on the print server. For example, you can automatically configure IP parameters over the network using BootP (Bootstrap Protocol) or DHCP (Dynamic Host Configuration Protocol) each time the printer is turned on. Or, you can manually configure IP parameters using one of the following methods: G the Install Network Printer wizard on the HP JetDirect CD-ROM G the printer's control panel (see chapter 3), G Telnet (see the HP JetDirect administrator's guide supplied electronically on the HP JetDirect CD-ROM), G Using the TCP/IP "arp -s" command, G HP Web JetAdmin or other management software. If the HP JetDirect print server does not receive it's IP configuration within two minutes after power up, a default IP address is automatically assigned: 192.0.0.192. This address is not a valid IP address for your network but can be used to initially access the JetDirect print server. However, to use the default IP address, you must temporarily set up your system with the same IP network number or establish a route to it. After an IP address is established on the print server, perform the following steps: 1. Run a supported version of your web browser. 2. Enter the IP address of the print server as the URL. The HP JetDirect main web page will be displayed. Click the "?" icon on the web page for more information. Using the Embedded Web Server 4-3 Embedded 4 Web Server

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Using the Embedded Web Server 4-3
Embedded
Web Server
4
Viewing the Embedded Web Server
Before you can use the embedded web server, the HP JetDirect print
server must be configured with an IP address.
There are many ways to configure an IP address on the print server.
For example, you can
automatically
configure IP parameters over
the network using BootP (Bootstrap Protocol) or DHCP (Dynamic
Host Configuration Protocol) each time the printer is turned on. Or,
you can
manually
configure IP parameters using one of the
following methods:
●
t
he
Install Network Printer
wizard on the HP JetDirect CD-ROM
●
the printer
’
s control panel (see chapter 3
),
●
Telnet (see the HP JetDirect administrator
’
s guide supplied
electronically on the HP JetDirect CD-ROM),
●
Using the TCP/IP
“
arp -s
”
command,
●
HP Web JetAdmin or other management software.
If the HP JetDirect print server does not receive it
’
s IP configuration
within two minutes after power up, a default IP address is
automatically assigned: 192.0.0.192. This address is not a valid
IP address for your network but can be used to initially access the
JetDirect print server. However, to use the default IP address, you
must temporarily set up your system with the same IP
network
number
or establish a route to it.
After an IP address is established on the print server, perform the
following steps:
1.
Run a supported version of your web browser.
2.
Enter the IP address of the print server as the URL.
The HP JetDirect main web page will be displayed.
Click the
“
?
”
icon on the web page for more information.