HP J3111A HP JetDirect 600N Print Server Hardware Installation Guide - 5969-68 - Page 35

To con TCP/IP parameters, TCP/IP=ON, EIO # JETDIRECT MENU, CFG NETWORK=NO

Get HP J3111A - JetDirect 600N Network Card PDF manuals and user guides
UPC - 002421211157
View all HP J3111A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Note The card must be configured with a valid IP address to operate on a TCP/IP network. For DHCP (Dynamic Host Configuration Protocol) operation, BOOTP must be enabled. If an IP address is configured through DHCP and is subsequently changed through the control panel, the DHCP assigned address is released. If a printer is configured through DHCP, and you manually change the subnet mask or default gateway through the control panel, you should also change the IP address. To configure TCP/IP parameters If you have not already done so, enable TCP/IP (TCP/IP=ON*) by following the instructions described in "To Enable or Disable Network Protocols" earlier in this chapter. Note Enter data carefully. If you make an incorrect entry, you cannot change it without starting again from step 1. 1. Take the printer offline by pressing [Go]. The "Ready" LED should be off. 2. Press [Menu] repeatedly until EIO # JETDIRECT MENU is displayed (# identifies the EIO slot number of the card). 3. Press [Item] until CFG NETWORK=NO* appears. NO* indicates that access to the EIO JetDirect network menus will be bypassed. You must change this to CFG NETWORK=YES* to access the EIO JetDirect menus: a. Press [Value]. CFG NETWORK=YES appears. b. Press [Select]. CFG NETWORK=YES* appears. Control Panel 3 Configuration Control Panel Configuration 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Control Panel Configuration 3-9
Control Panel
Configuration
3
Note
The card must be configured with a valid IP address
to operate on a TCP/IP network.
For DHCP (Dynamic Host Configuration Protocol)
operation, BOOTP must be enabled.
If an IP address is configured through DHCP and is
subsequently changed through the control panel,
the DHCP assigned address is released.
If a printer is configured through DHCP, and you
manually change the subnet mask or default
gateway through the control panel, you should
also change the IP address.
To configure TCP/IP parameters
If you have not already done so, enable TCP/IP (
TCP/IP=ON*
) by
following the instructions described in
“
To Enable or Disable
Network Protocols
”
earlier in this chapter.
Note
Enter data carefully. If you make an incorrect entry,
you cannot change it without starting again from
step 1.
1.
Take the printer offline by pressing
[Go]
. The
“
Ready
”
LED
should be off.
2.
Press
[Menu]
repeatedly until
EIO # JETDIRECT MENU
is displayed
(# identifies the EIO slot number of the card).
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
NO*
indicates that access to the EIO JetDirect network menus
will be bypassed. You must change this to
CFG NETWORK=YES*
to
access the EIO JetDirect menus:
a.
Press
[Value]
.
CFG NETWORK=YES
appears.
b.
Press
[Select]
.
CFG NETWORK=YES*
appears.