HP J3111A HP JetDirect 600N Print Server Hardware Installation Guide - 5969-68 - Page 37

Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only), To con EtherTalk parameters

Get HP J3111A - JetDirect 600N Network Card PDF manuals and user guides
UPC - 002421211157
View all HP J3111A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Control Panel 3 Configuration Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) You can configure Apple EtherTalk parameters if the Apple EtherTalk protocol is enabled (ETALK=ON*), and the PostScript printer language is enabled. To ensure the PostScript printer language is enabled, check the printer's CONFIGURATION MENU. PERSONALTY=PS* or PERSONALTY=AUTO* should be set. To configure EtherTalk parameters If you haven't already done so, enable EtherTalk by following the instructions described in "To Enable or Disable Network Protocols" in this chapter. 1. Take the printer offline by pressing [Go]. The "Ready" LED should be off. 2. Press [Menu] repeatedly until EIO # JETDIRECT MENU is displayed (# identifies the EIO slot number of the card). 3. Press [Item] until CFG NETWORK=NO* appears. NO* indicates that access to the EIO JetDirect network menus will be bypassed. You must change this to CFG NETWORK=YES* to access the EIO JetDirect menus: a. Press [Value]. CFG NETWORK=YES appears. b. Press [Select]. CFG NETWORK=YES* appears. 4. Press [Item] to scroll through each network protocol until CFG ETALK=NO* is displayed. To access the EtherTalk configuration menu, press [Value] and then press [Select] to display CFG ETALK=YES*. 5. Press [Item]. ETALK PHASE=1* or ETALK PHASE=2* appears. I The asterisk (*) indicates the active phase setting. I To change the phase setting, press [Value] until the phase setting that you desire appears, then press [Select]. Be sure "*" appears alongside your selection. 6. To activate the printer and save your changes, press [Go]. Control Panel Configuration 3-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Control Panel Configuration 3-11
Control Panel
Configuration
3
Configuring Apple EtherTalk Phase
Parameters (Ethernet Cards Only)
You can configure Apple EtherTalk parameters if the Apple
EtherTalk protocol is enabled (
ETALK=ON*
), and the PostScript
printer language is enabled.
To ensure the PostScript printer language is enabled, check the
printer
’
s
CONFIGURATION MENU
.
PERSONALTY=PS*
or
PERSONALTY=AUTO*
should be set.
To configure EtherTalk parameters
If you haven't already done so, enable EtherTalk by following the
instructions described in
“
To Enable or Disable Network Protocols
”
in this chapter.
1.
Take the printer offline by pressing
[Go]
. The
“
Ready
”
LED
should be off.
2.
Press
[Menu]
repeatedly until
EIO # JETDIRECT MENU
is displayed
(# identifies the EIO slot number of the card).
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
NO*
indicates that access to the EIO JetDirect network menus
will be bypassed. You must change this to
CFG NETWORK=YES*
to
access the EIO JetDirect menus:
a.
Press
[Value]
.
CFG NETWORK=YES
appears.
b.
Press
[Select]
.
CFG NETWORK=YES*
appears.
4.
Press
[Item]
to scroll through each network protocol until
CFG ETALK=NO*
is displayed.
To access the EtherTalk configuration menu, press
[Value]
and
then press
[Select]
to display
CFG ETALK=YES*
.
5.
Press
[Item]
.
ETALK PHASE=1*
or
ETALK PHASE=2*
appears.
■
The asterisk (*) indicates the active phase setting.
■
To change the phase setting, press
[Value]
until the phase
setting that you desire appears, then press
[Select]
. Be sure
“
*
”
appears alongside your selection.
6.
To activate the printer and save your changes, press
[Go]
.