HP J3111A HP JetDirect 600N Print Server Hardware Installation Guide - 5969-68 - Page 31

To con an IPX frame type

Get HP J3111A - JetDirect 600N Network Card PDF manuals and user guides
UPC - 002421211157
View all HP J3111A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

To configure an IPX frame type If you have not already done so, enable the IPX/SPX protocol (IPX/SPX=ON*) by following the instructions described in "To enable or disable network protocols" in this chapter. 1. Take the printer offline by pressing [Go]. The "Ready" LED should be off. 2. Press [Menu] repeatedly until EIO # JETDIRECT MENU is displayed (# identifies the EIO slot number of the card). 3. Press [Item] until CFG NETWORK=NO* appears. NO* indicates that access to the EIO JetDirect network menus will be bypassed. You must change this to CFG NETWORK=YES* to access the EIO JetDirect menus: a. Press [Value]. CFG NETWORK=YES appears. b. Press [Select]. CFG NETWORK=YES* appears. 4. Press [Item] to scroll through each network protocol until CFG IPX/SPX=NO* is displayed. To access the IPX/SPX configuration menu, press [Value] and then press [Select] to display CFG IPX/SPX=YES*. 5. Press [Item] until FRAME=* appears. AUTO EN_8023 EN_II EN_8022 EN_SNAP TR_8022 TR_SNAP G To change the frame type, press [Value] until the desired option appears, and then press [Select]. G Press [Item] to continue to the next parameter. Note: An asterisk (*) indicates the active frame type selected. The available frame type options depend on whether you have an Ethernet or Token Ring card installed. 6. To activate the printer and save your changes, press [Go]. Control Panel 3 Configuration Control Panel Configuration 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Control Panel Configuration 3-5
Control Panel
Configuration
3
To configure an IPX frame type
If you have not already done so, enable the IPX/SPX protocol
(
IPX/SPX=ON*
) by following the instructions described in
“
To enable
or disable network protocols
”
in this chapter.
1.
Take the printer offline by pressing
[Go]
. The
“
Ready
”
LED
should be off.
2.
Press
[Menu]
repeatedly until
EIO # JETDIRECT MENU
is displayed
(# identifies the EIO slot number of the card).
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
NO*
indicates that access to the EIO JetDirect network menus
will be bypassed. You must change this to
CFG NETWORK=YES*
to
access the EIO JetDirect menus:
a.
Press
[Value]
.
CFG NETWORK=YES
appears.
b.
Press
[Select]
.
CFG NETWORK=YES*
appears.
4.
Press
[Item]
to scroll through each network protocol until
CFG IPX/SPX=NO*
is displayed.
To access the IPX/SPX configuration menu, press
[Value]
and
then press
[Select]
to display
CFG IPX/SPX=YES*
.
5.
Press
[Item]
until
FRAME=<Frame Type>*
appears.
6.
To activate the printer and save your changes, press
[Go]
.
AUTO
EN_8023
EN_II
EN_8022
EN_SNAP
TR_8022
TR_SNAP
●
To change the frame type, press
[Value]
until
the desired option appears, and then press
[Select]
.
●
Press
[Item]
to continue to the next
parameter.
Note:
An asterisk (*) indicates the active frame type selected.
The available frame type options depend on whether you have an
Ethernet or Token Ring card installed.