HP Pro Mini 260 G9 Desktop PC Maintenance and Service Guide - Page 31

Solid-state drive

Get HP Pro Mini 260 G9 Desktop PC PDF manuals and user guides View all HP Pro Mini 260 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

2. Lift the connector latch on the system board, and then pull the tab (1) to disconnect the hard drive cable (2). 3. Remove the two Torx T15 screws (3) that secure the hard drive cage to the chassis. 4. Slide the hard drive cage back, and then lift it out of the chassis (4). NOTE: Computer appearance might vary. Solid-state drive To remove the solid-state drive module, use these procedures. The solid-state drive is located under the hard drive and drive cage. For list of available solid-state drives, see Computer major components on page 4. Before removing the solid-state drive module, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 16). 2. Remove the access panel (see Access panel on page 16). 3. If installed, remove the hard drive and drive cage (see Hard drive and drive cage on page 23). Remove the solid-state drive module: 24 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2.
Lift the connector latch on the system board, and then pull the tab
(1)
to disconnect the hard drive cable
(2)
.
3.
Remove the two Torx T15 screws
(3)
that secure the hard drive cage to the chassis.
4.
Slide the hard drive cage back, and then lift it out of the chassis
(4)
.
NOTE:
Computer appearance might vary.
Solid-state drive
To remove the solid-state drive module, use these procedures. The solid-state drive is located under the hard
drive and drive cage.
For list of available solid-state drives, see
Computer major components
on page
4
.
Before removing the solid-state drive module, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
16
).
2.
Remove the access panel (see
Access panel
on page
16
).
3.
If installed, remove the hard drive and drive cage (see
Hard drive and drive cage
on page
23
).
Remove the solid-state drive module:
24
Chapter 4
Removal and replacement procedures