HP Pro Mini 260 G9 Desktop PC Maintenance and Service Guide - Page 42

Wireless antennas and cables, Remove the fan see

Get HP Pro Mini 260 G9 Desktop PC PDF manuals and user guides View all HP Pro Mini 260 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Table 4-2 System board callouts Item Component (1) Speaker (2) WLAN module (3) Solid-state drive (4) Flex I/O board (5) RTC battery Item Component (6) Hard drive (7) CMOS button (8) Fan (9) Memory module (10) Memory module Wireless antennas and cables To remove the wireless antennas and cables, use these procedures. The cables route from the WLAN module to the antennas mounted on the front of the computer. Before removing the wireless antennas and cables, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 16). 2. Remove the access panel (see Access panel on page 16). 3. Remove the fan (see Fan on page 21). 4. Remove the heat sink (see Processor heat sink on page 31). 5. If installed, remove flex I/O connector board (see Flex I/O connector board on page 30). 6. If installed, remove the hard drive and drive cage (see Hard drive and drive cage on page 23). Remove the wireless antennas: 1. From the inside of the chassis, remove the antenna cables from the clips (1). 2. From the front of the chassis, remove the Phillips screw from each antenna (2). 3. Pull the antennas and cables out of the front of the chassis (3). Wireless antennas and cables 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Table 4-2
System board callouts
Item
Component
Item
Component
(1)
Speaker
(6)
Hard drive
(2)
WLAN module
(7)
CMOS button
(3)
Solid-state drive
(8)
Fan
(4)
Flex I/O board
(9)
Memory module
(5)
RTC battery
(10)
Memory module
Wireless antennas and cables
To remove the wireless antennas and cables, use these procedures. The cables route from the WLAN module
to the antennas mounted on the front of the computer.
Before removing the wireless antennas and cables, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
16
).
2.
Remove the access panel (see
Access panel
on page
16
).
3.
Remove the fan (see
Fan
on page
21
).
4.
Remove the heat sink (see
Processor heat sink
on page
31
).
5.
If installed, remove flex I/O connector board (see
Flex I/O connector board
on page
30
).
6.
If installed, remove the hard drive and drive cage (see
Hard drive and drive cage
on page
23
).
Remove the wireless antennas:
1.
From the inside of the chassis, remove the antenna cables from the clips
(1)
.
2.
From the front of the chassis, remove the Phillips screw from each antenna
(2)
.
3.
Pull the antennas and cables out of the front of the chassis
(3)
.
Wireless antennas and cables
35