HP Pro Mini 260 G9 Desktop PC Maintenance and Service Guide - Page 37

Flex I/O connector board, Before removing flex I/O connector board, follow these steps

Get HP Pro Mini 260 G9 Desktop PC PDF manuals and user guides View all HP Pro Mini 260 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2. Remove the access panel (see Access panel on page 16). 3. If installed, remove the hard drive and drive cage (see Hard drive and drive cage on page 23). Remove the speaker: 1. Disconnect the speaker cable from the system board connector (1). 2. From the outside-front, slide the rubber grommets upward (2). 3. Pull the speaker into the computer to remove it (3). NOTE: Computer appearance might vary. To install the speaker, reverse the removal procedures. Flex I/O connector board To remove flex I/O connector board #1, use these procedures. Before removing flex I/O connector board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 16). 2. Remove the access panel (see Access panel on page 16). 3. If installed, remove the hard drive and drive cage (see Hard drive and drive cage on page 23). Remove flex I/O connector board: ▲ Remove the two Phillips screws that secure the board to the computer (1), and then lift the board to disconnect it from the connector on the system board (2). NOTE: Computer appearance might vary. 30 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2.
Remove the access panel (see
Access panel
on page
16
).
3.
If installed, remove the hard drive and drive cage (see
Hard drive and drive cage
on page
23
).
Remove the speaker:
1.
Disconnect the speaker cable from the system board connector
(1)
.
2.
From the outside-front, slide the rubber grommets upward
(2)
.
3.
Pull the speaker into the computer to remove it
(3)
.
NOTE:
Computer appearance might vary.
To install the speaker, reverse the removal procedures.
Flex I/O connector board
To remove flex I/O connector board #1, use these procedures.
Before removing flex I/O connector board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
16
).
2.
Remove the access panel (see
Access panel
on page
16
).
3.
If installed, remove the hard drive and drive cage (see
Hard drive and drive cage
on page
23
).
Remove flex I/O connector board:
▲
Remove the two Phillips screws that secure the board to the computer
(1)
, and then lift the board to
disconnect it from the connector on the system board
(2)
.
NOTE:
Computer appearance might vary.
30
Chapter 4
Removal and replacement procedures