HP Surestore 64 HP Enterprise Connectivity Fabric Manager User's Guide - Page 109

Default Zone, Con Start, Close, Messages appear in the Status area

Get HP Surestore 64 - Director Switch PDF manuals and user guides View all HP Surestore 64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

be in the default zone. If a zone set is active, then all connected devices that are not included in at least one of the zones in the active zone set are included in the default zone. Enabling the default zone allows any device in the default zone to see any other device in the default zone. If the default zone is disabled and no zone set is active, then devices connected to the product cannot communicate. To disable or enable the default zone, perform the following steps: 1. In either the Zoning View or the Topology View, choose Default Zone from the Configure menu. The Configure Default Zone dialog box displays (Figure 43). A message at the top of the dialog box indicates whether the default zone is currently enabled or disabled. The preferred mode is disabled. Figure 43 Configure Default Zone Dialog Box 2. To enable or disable the default zone, click Start. Messages appear in the Status area indicating the progress of the command. Buttons on the dialog box disable until the process is complete. When the process finishes, the Start button changes to a Close button. 3. Click Close to close the dialog box. Configuring and Managing Zoning 91 Fabric Zoning

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
Configuring and Managing Zoning
91
Fabric Zoning
be in the default zone. If a zone set is active, then all connected devices that are not
included in at least one of the zones in the active zone set are included in the default zone.
Enabling the default zone allows any device in the default zone to see any other device in
the default zone. If the default zone is disabled and no zone set is active, then devices
connected to the product cannot communicate.
To disable or enable the default zone, perform the following steps:
1.
In either the Zoning View or the Topology View, choose
Default Zone
from the
Configure
menu.
The Configure Default Zone dialog box displays (Figure 43). A message at the top of
the dialog box indicates whether the default zone is currently enabled or disabled. The
preferred mode is disabled.
Figure 43
Configure Default Zone Dialog Box
2.
To enable or disable the default zone, click
Start
. Messages appear in the Status area
indicating the progress of the command. Buttons on the dialog box disable until the
process is complete.
When the process finishes, the
Start
button changes to a
Close
button.
3.
Click
Close
to close the dialog box.