HP Surestore Tape Library Model 6/60 SAN Solution Installation Guide - Page 24

Managing the Switch Using the Telnet Options

Get HP Surestore Tape Library Model 6/60 PDF manuals and user guides View all HP Surestore Tape Library Model 6/60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Table 2-1 Installation Switches If the default address cannot be used in your network configuration, you will need to make a serial (RS-232) connection to the switch using terminal emulation software. To do this, you will need a standard serial cable with a female 9-pin D-Sub connector for the switch connection and an appropriate connector for the host/terminal being used. The cabling pinout is described in the table below. Serial Connection Pinout for Brocase SilkWorm™ 2400 Switch Pin 1 2 3 4 5 6 7 8 9 Signal TxData RxData GND CTS - Description Transmit data Receive data Logic ground Clear to send (must be driven high) - Managing the Switch Using the Telnet Options: 1. Connect the host system and the switch using the serial cable. 2. Start the terminal emulation software on the host system. 3. Power-on the switch. The switch will automatically connect, and you will be logged in as admin. If you are prompted for a login and password: 1. Enter [admin] and [password] respectively. 2. Enter the command [ipAddrSet]. You will be prompted to enter the Ethernet and FC IP addresses, subnet mask, and gateway address. 3. If the current value displayed is correct, select [ENTER]. The switch should now be accessible using Telnet. 2-6 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Installation
Switches
Chapter 2
2-6
If the default address cannot be used in your network configuration, you
will need to make a serial (RS-232) connection to the switch using
terminal emulation software. To do this, you will need a standard serial
cable with a female 9-pin D-Sub connector for the switch connection and
an appropriate connector for the host/terminal being used.
The cabling pinout is described in the table below.
Managing the Switch Using the Telnet Options:
1.
Connect the host system and the switch using the serial cable.
2.
Start the terminal emulation software on the host system.
3.
Power-on the switch.
The switch will automatically connect, and you will be logged in as
admin. If you are prompted for a login and password:
1. Enter
[admin]
and
[password]
respectively.
2.
Enter the command
[ipAddrSet]
. You will be prompted to enter the
Ethernet and FC IP addresses, subnet mask, and gateway address.
3.
If the current value displayed is correct, select
[ENTER]
. The switch
should now be accessible using Telnet.
Table 2-1
Serial Connection Pinout for Brocase SilkWorm
2400 Switch
Pin
Signal
Description
1
-
-
2
TxData
Transmit data
3
RxData
Receive data
4
-
-
5
GND
Logic ground
6
-
-
7
CTS
Clear to send (must be driven high)
8
-
-
9
-
-