HP Surestore Tape Library Model 6/60 SAN Solution Installation Guide - Page 35

HP SureStore E Tape Library Models 10/180

Get HP Surestore Tape Library Model 6/60 PDF manuals and user guides View all HP Surestore Tape Library Model 6/60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

NOTE NOTE CAUTION Installation Tape Libraries 5. Enter the designated IP address into the Web browser to launch the Web-Based Library Administrator pages. Example: IP address = 15.28.33.12 Device name = library1 http://library1 or http://15.28.33.12 Instructions and help screens describing this Web-based management are available online on the Web-Based Library Administration pages under online help. HP SureStore E Tape Library Models 10/180 and 20/700 Please read through this section thoroughly before beginning the configuration process. Current SAN support for these libraries requires using either the HP SureStore E Bridge FC 4/1 HV or the HP SureStore E SCSI Bridge FC 4/2. It is recommended that you DO NOT enable Auto Clean as it may interfere with the operation of backup software. This section describes how to configure the library and tape drives for operation. Configuration requires you to: • Enable Auto Clean, if desired, (Model 20/700 only) by installing cleaning cartridges (see "Enabling Auto Clean"). • Power-on or reset the library (either of which initializes the library). • Enter the required configuration information. • Place the library online. • Send a host or client command to load library audit information into the host or client memory. Chapter 2 2-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Installation
Tape Libraries
Chapter 2
2-17
5.
Enter the designated IP address into the Web browser to launch the
Web-Based Library Administrator pages.
Example:
IP address = 15.28.33.12
Device name = library1
http://library1 or http://15.28.33.12
Instructions and help screens describing this Web-based
management are available online on the Web-Based Library
Administration pages under online help.
HP SureStore E Tape Library Models 10/180 and
20/700
NOTE
Please read through this section thoroughly before beginning the
configuration process.
NOTE
Current SAN support for these libraries requires using either the HP
SureStore E Bridge FC 4/1 HV or the HP SureStore E SCSI Bridge FC 4/2.
CAUTION
It is recommended that you
DO NOT
enable Auto Clean as it may
interfere with the operation of backup software.
This section describes how to configure the library and tape drives for
operation. Configuration requires you to:
•
Enable Auto Clean,
if desired
, (Model 20/700 only) by installing
cleaning cartridges (see “Enabling Auto Clean”).
•
Power-on or reset the library (either of which initializes the library).
•
Enter the required configuration information.
•
Place the library online.
•
Send a host or client command to load library audit information into
the host or client memory.