HP Tc2100 hp server tc2100 installation sheet (English) - Page 32

IDE Mass Storage Devices, IDE Controller Configuration

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 4 Installing Mass Storage Devices NOTE The boot order can be changed using the Server's (BIOS) Setup Utility. Refer to Chapter 8, "Configuring the HP Server" for more information. IDE Mass Storage Devices This section provides the configuration of the IDE mass storage devices, if you have selected an IDE version of the HP Server tc2100. IDE Controller Configuration The embedded IDE controller is available for both models (IDE or SCSI) of the HP Server. The embedded IDE controller is an Ultra DMA33/66/100 E-IDE dual channel controller, which provides IDE-1 and IDE-2 connectors. Each channel can only control two IDE devices. The IDE Server model uses the IDE-1 for the boot drive and the IDE-2 connector for the IDE CD-ROM. The Setup Utility (BIOS) can be used to change the boot order of the flexible disk drive and the IDE devices. Refer to Chapter 8, "Configuring the HP Server," for more information. IDE Mass Storage Additions Table 4-1 lists the number and types of mass storage devices that may be added to the IDE model of the HP Server. Table 4-1. IDE Model Mass Storage Devices Interface Types FDD IDE-2 Max No. Devices 1 2 IDE-1 2 SCSI 1 controller board Installed Devices and Addresses Factory installed flexible disk drive (FDD) in shelf 1 • Factory installed CD-ROM drive in shelf 2 • Optional 3rd IDE hard drive in shelf 4 • Factory installed IDE hard drive in shelf 6 • Optional 2nd IDE hard drive in shelf 5 • Optional SCSI backup tape drive in shelf 3 (SCSI controller board required for SCSI back up tape drive) 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 4
Installing Mass Storage Devices
26
NOTE
The boot order can be changed using the Server's (BIOS) Setup
Utility. Refer to Chapter 8, "Configuring the HP Server" for
more information.
IDE Mass Storage Devices
This section provides the configuration of the IDE mass storage devices, if you
have selected an IDE version of the HP Server tc2100.
IDE Controller Configuration
The embedded IDE controller is available for both models (IDE or SCSI) of the
HP Server. The embedded IDE controller is an Ultra DMA33/66/100 E-IDE dual
channel controller, which provides IDE-1 and IDE-2 connectors. Each channel can
only control two IDE devices.
The IDE Server model uses the IDE-1 for the boot drive and the IDE-2 connector
for the IDE CD-ROM. The Setup Utility (BIOS) can be used to change the boot
order of the flexible disk drive and the IDE devices. Refer to Chapter 8,
"Configuring the HP Server," for more information.
IDE Mass Storage Additions
Table 4-1 lists the number and types of mass storage devices that may be added to
the IDE model of the HP Server.
Table 4-1. IDE Model Mass Storage Devices
Interface
Types
Max No.
Devices
Installed Devices and Addresses
FDD
1
Factory installed flexible disk drive (FDD) in shelf 1
IDE-2
2
•
Factory installed CD-ROM drive in shelf 2
•
Optional 3rd IDE hard drive in shelf 4
IDE-1
2
•
Factory installed IDE hard drive in shelf 6
•
Optional 2nd IDE hard drive in shelf 5
SCSI
controller
board
1
•
Optional SCSI backup tape drive in shelf 3 (SCSI
controller board required for SCSI back up tape drive)