HP Tc2100 hp server tc2100 installation sheet (English) - Page 39

Adding Third Hard Disk Drive

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 4 Installing Mass Storage Devices e. Refer to the documentation provided with the hard drive. CAUTION All mounting screws used to thread into the hard disk drive must be #6-32 and not exceed ¼-inch in length. Longer screws may cause internal damage to the mass storage device. Damage caused by incorrect mounting screws is not covered by the HP warranty. 7. Install the hard disk drive, as described below: a. Place the hard disk drive into the tray and use the screws provided to secure it to the tray from the bottom. See Figure 4-4. b. Insert the hard disk drive assembly into the fourth shelf. See Figure 4-4. The tabs should snap into place when the drive tray is pushed all of the way into the fourth shelf. B A CAUTION Figure 4-4. Adding Third Hard Disk Drive Install and remove connectors carefully, and avoid bending any of the pins. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 4
Installing Mass Storage Devices
33
e.
Refer to the documentation provided with the hard drive.
CAUTION
All mounting screws used to thread into the hard disk drive
must be #6-32 and not exceed ΒΌ-inch in length. Longer
screws may cause
internal damage to the mass storage device.
Damage caused by incorrect mounting screws is not covered
by the HP warranty.
7. Install the hard disk drive, as described below:
a.
Place the hard disk drive into the tray and use the screws provided to
secure it to the tray from the bottom. See Figure 4-4.
b. Insert the hard disk drive assembly into the fourth shelf. See Figure 4-4.
The tabs should snap into place when the drive tray is pushed all of the
way into the fourth shelf.
B
A
Figure 4-4. Adding Third Hard Disk Drive
CAUTION
Install and remove connectors carefully, and avoid bending
any of the pins.