HP Tc2100 hp server tc2100 installation sheet (English) - Page 51

Installing Additional Boards, Introduction, Tested PCI Boards, Tools Required

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

6 Installing Additional Boards Introduction The system board in the HP Tower Server tc2100 provides up to five PCI slots (P1 through P5), with five 32-bits slots at 33 MHz bus speed. The SCSI model requires the first slot, (P1) for the SCSI controller board. Tested PCI Boards For a list of tested PCI boards, check for compatibility in the Hardware Tested Products list for the HP Server tc2100 under the Technical Support topic for the specific NOS used in the Server at HP's web site: http://www.hp.com/Server/support/ CAUTION Some accessory board outputs may exceed U.S. National Electrical code (NFPA 70) Class 2 or limited power source limits and must use appropriate interconnecting cabling in accordance with the National Electrical Code. NOTE All Hewlett-Packard accessory boards comply with the U.S. National Electrical code (NFPA 70) Class 2. Refer to Chapter 8, "Configuring the HP Server," for more information. Tools Required These tools may be needed for preparing the accessory boards for installation in the Server: • Torx T-15 screwdriver • ¼-inch flat blade screwdriver • An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
45
6 Installing Additional Boards
Introduction
The system board in the HP Tower Server tc2100 provides up to five PCI slots
(P1 through P5), with five 32-bits slots at 33 MHz bus speed. The SCSI model
requires the first slot, (P1) for the SCSI controller board.
Tested PCI Boards
For a list of tested PCI boards, check for compatibility in the Hardware Tested
Products list for the HP Server tc2100 under the Technical Support topic for the
specific NOS used in the Server at HP’s web site:
CAUTION
Some accessory board outputs may exceed U.S. National
Electrical code (NFPA 70) Class 2 or limited power source
limits and must use appropriate interconnecting cabling in
accordance with the National Electrical Code.
NOTE
All Hewlett-Packard accessory boards comply with the U.S.
National Electrical code (NFPA 70) Class 2.
Refer to Chapter 8, "Configuring the HP Server," for more information.
Tools Required
These tools may be needed for preparing the accessory boards for installation in
the Server:
•
Torx T-15 screwdriver
•
¼-inch flat blade screwdriver
•
An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.