HP Tc2100 hp server tc2100 installation sheet (English) - Page 40

Installing an Optional Backup Tape Drive

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 4 Installing Mass Storage Devices 8. Connect the data cable to the hard disk drive, as described below: Refer to Figure 4-1. o If mounting a third IDE hard drive, connect the secondary (IDE-2) cable to hard drive. The secondary cable is connected to the IDE CD-ROM and should have an available connector for the third IDE hard disk drive. o If mounting a third SCSI hard drive, connect the SCSI cable to the drive and ensure all SCSI drives are connected to the SCSI cable. There are five connectors on the standard SCSI cable, with four of the connectors intended for the three hard disk drives and one optional backup tape drive. The standard SCSI cable has a terminator at the end of the cable. 9. Connect the power cable to the rear of the hard disk drive. 10. Replace the upper bezel and the left side cover. 11. Replace the external cables, power cord, and then restore power to the Server. The BIOS and SCSISelect utilities automatically detect the new hard drives (IDE or SCSI), but you should check the BIOS and SCSISelect settings and make changes as necessary. Installing an Optional Backup Tape Drive The optional HP SureStore DAT 24i backup tape drive is a single-ended device and may slow down the disk access time for the Ultra-160 SCSI drives. A second SCSI controller board may be required to separately control the backup tape drive. 1. If the Server is already installed and operating, power-down the Server. Refer to Chapter 2, "Controls, Ports, and Indicators." 2. Disconnect the power cables and any external cables connected to the Server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover from the Server. Refer to Chapter 3, "Opening and Closing the HP Server." 4. Remove the upper front bezel. Refer to Chapter 3, "Opening and Closing the HP Server." 5. Press in on both tab latches to release the third drive tray and pull it out at the same time. See Figures 4-1 and 4-5. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 4
Installing Mass Storage Devices
34
8. Connect the data cable to the hard disk drive, as described below:
Refer to Figure 4-1.
o
If mounting a third IDE hard drive, connect the secondary (IDE-2) cable to
hard drive.
The secondary cable is connected to the IDE CD-ROM and should have an
available connector for the third IDE hard disk drive.
o
If mounting a third SCSI hard drive, connect the SCSI cable to the drive
and ensure all SCSI drives are connected to the SCSI cable.
There are five connectors on the standard SCSI cable, with four of the
connectors intended for the three hard disk drives and one optional backup
tape drive. The standard SCSI cable has a terminator at the end of the
cable.
9. Connect the power cable to the rear of the hard disk drive.
10. Replace the upper bezel and the left side cover.
11. Replace the external cables, power cord, and then restore power to the Server.
The BIOS and SCSISelect utilities automatically detect the new hard drives
(IDE or SCSI), but you should check the BIOS and SCSISelect settings and
make changes as necessary.
Installing an Optional Backup Tape Drive
The optional HP SureStore DAT 24i backup tape drive is a single-ended device
and may slow down the disk access time for the Ultra-160 SCSI drives. A second
SCSI controller board may be required to separately control the backup tape drive.
1. If the Server is already installed and operating, power-down the Server.
Refer to Chapter 2, "Controls, Ports, and Indicators."
2. Disconnect the power cables and any external cables connected to the Server.
If necessary, label each one to expedite re-assembly.
3. Remove the left side cover from the Server.
Refer to Chapter 3, "Opening and Closing the HP Server."
4. Remove the upper front bezel.
Refer to Chapter 3, "Opening and Closing the HP Server."
5. Press in on both tab latches to release the third drive tray and pull it out at the
same time. See Figures 4-1 and 4-5.