Home » HP Manuals » Desktops » HP Tc2100 » Manual Viewer

HP Tc2100 hp server tc2100 installation sheet (English) - Page 97

Battery Safety Statements, Accessory Board Safety Statements, Battery Safety - United States

Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Appendix B Regulatory Information Battery Safety Statements This product uses a lithium battery. Battery Safety - United States WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Accessory Board Safety Statements Accessory Board Safety - United States CAUTION Some accessory board outputs may exceed U.S. National Electrical code (NFPA 70) Class 2 (limited) or power source limits and must use appropriate interconnecting cabling in accordance with the National Electrical Code. NOTE All Hewlett-Packard accessory boards comply with the U.S. National Electrical code (NFPA 70) Class 2. 91

Section	Page
1 Setting Up the HP Server	7
Setup Steps	7
Preparations	7
Installing the HP Server	7
Installing Options	7
Applying Power to the Server	10
2 Controls, Ports, and Indicators	13
Introduction	13
Front Panel	13
Additional Front Panel Controls and Indicators	14
Rear View	16
Applying Power to the HP Server	17
Powering-Up the Server	18
Powering-Down the Server	19
Connecting AC Power to Multiple-Server Configurations	19
Sleep States (ACPI)	19
3 Opening and Closing the HP Server	23
Introduction	23
Tools Required	23
Removing the Covers	23
Removing the Side Cover	24
Removing the Front Bezel	25
Replacing the Upper Front Bezel	26
Replacing the Left Side Cover	27
4 Installing Mass Storage Devices	29
Introduction	29
Tools Required	29
Mass Storage Guidelines	29
Boot Priority	31
IDE Mass Storage Devices	32
IDE Controller Configuration	32
IDE Mass Storage Additions	32
SCSI Mass Storage Devices	33
SCSI Controller Configuration	33
SCSI Mass Storage Additions	34
Installing a Second Hard Disk Drive	34
Installing a Third Hard Disk Drive	38
Installing an Optional Backup Tape Drive	40
5 Installing Additional Memory	43
Introduction	43
Tools Required	43
Memory Installation Guidelines	43
Installing Additional DIMMs	44
Removing DIMMs	48
6 Installing Additional Boards	51
Introduction	51
Tested PCI Boards	51
Tools Required	51
Accessory Board Installation Guidelines	52
IRQ Settings	52
Installing a Disk Array Controller Board	52
Boot Priority	52
Installing Accessory Boards	54
Removing Accessory Boards	59
7 Connecting the Monitor, Keyboard, Mouse, and UPS	61
Introduction	61
Connecting the UPS (Uninterruptible Power Supply)	62
8 Configuring the HP Server	63
Introduction	63
HP Startup CD-ROM	64
Accessing the HP Startup CD-ROM	64
Contents of the HP Startup CD-ROM	65
NOS Installation	65
DiagTools	65
Setup (BIOS) Utility	66
Accessing the Setup Utility	66
Menu Bar	66
Using the Setup Screens	69
Changing the System Date and Time	69
Setting Boot Passwords	70
SCSI Configuration Utility	73
9 Troubleshooting	75
Introduction	75
Tools Required	76
Common Installation Problems	76
Troubleshooting Sequence	77
Server Will Not Power On	77
Problems after Server is Powered On	78
Error Messages	79
POST Error Messages	81
POST Error Codes	82
Beep Codes	82
Clearing the CMOS Configuration	83
Resetting a Lost Password	84
Hardware Problems	85
Monitor Does Not Work	85
Keyboard or Mouse Does Not Work	86
CD-ROM Drive Does Not Work	86
SCSI Device Does Not Work	86
Replacing a Battery	87
Problems Running the Setup Utility	88
A Specifications	89
Introduction	89
Requirements	89
System Board Layout	92
B Regulatory Information	93
Regulatory Notices - Electromagnetic Compliance	93
Notice for United States	93
Declaration of Conformity (US and EU)	95
Regulatory Notices - Product Safety	96
CDROM and Laser Safety Statements	96
Battery Safety Statements	97
Accessory Board Safety Statements	97
C Service and Support	99
D Warranty and Software License	101
Warranty	101
HP Software Product License Agreement	101
Non-Nuclear Usage	102