HP Tc2100 hp server tc2100 installation sheet (English) - Page 88

Problems Running the Setup Utility, Battery on System Board

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Chapter 9 Troubleshooting View Rotated 90 Degrees CCW Figure 9-3. Battery on System Board 9. Insert the new battery with the positive sign (+) facing up in the socket. 10. Press down on the center of the battery with your thumb, pushing the battery down into the socket. The battery should snap into place. 11. Ensure the spring latch holds the battery firmly. 12. If necessary, replace the SCSI cable and replace the left side cover. 13. Power on the Server and reset the BIOS (CMOS) settings. Problems Running the Setup Utility If you cannot run the Setup Utility, the HP Server's configuration in CMOS memory may have been corrupted. The only way to recover from a corrupted configuration is to clear it. Refer to "Clearing the CMOS Configuration," earlier in this chapter and reset the BIOS configuration. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 9
Troubleshooting
82
View Rotated
90 Degrees CCW
Figure 9-3. Battery on System Board
9. Insert the new battery with the positive sign (+) facing up in the socket.
10. Press down on the center of the battery with your thumb, pushing the battery
down into the socket.
The battery should snap into place.
11. Ensure the spring latch holds the battery firmly.
12. If necessary, replace the SCSI cable and replace the left side cover.
13. Power on the Server and reset the BIOS (CMOS) settings.
Problems Running the Setup Utility
If you cannot run the Setup Utility, the HP Server's configuration in CMOS
memory may have been corrupted. The only way to recover from a corrupted
configuration is to clear it. Refer to "Clearing the CMOS Configuration," earlier in
this chapter and reset the BIOS configuration.