Hitachi L42S504 Owners Guide - Page 12

Quick Setup Guide - lcd tv s

Get Hitachi L42S504 - LCD Direct View TV PDF manuals and user guides View all Hitachi L42S504 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

RGB Quick Setup Guide Perform the following steps to quickly setup your new Hitachi LCD Television Set. 1. ANTENNA CONNECTION Unless your LCD Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. a). VHF (75-Ohm) antenna/CATV (Cable TV) When using a 75-Ohm coaxial cable system, connect the CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal. Air/Cable RGB Rear Panel Jack To outdoor Antenna or Cable TV (CATV) System To Air/Cable Terminal b). VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the TV Air/Cable terminal on the TV. To outdoor VHF or UHF Antenna To Air/CableTerminal Attach an optional antenna cable mixer to the TV Air/Cable terminal and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer. To UHF antenna Air/Cable To outdoor antenna or CATV system Antenna Mixer c). When both VHF and UHF antennas are connected NOTE Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial cable is recommended. 2. CONNECT YOUR NEW HITACHI LCD TV TO THE POWER SOURCE a). Connect the power cord to your TV set and secure it with the AC Wire Clamp (see page 7) . b). The Indicating Lamp will light red (Standby mode) and then light blue (picture is shown). AC Wire Clamp Indicating Lamp a). Connect the power cord to the AC wall outlet . 4 3. POWER ON/OFF YOUR NEW HITACHI LCD TV Press the POWER button on the Remote Control or the POWER or 5 button on the Side Control Panel to power on/off the LCD TV. For Stand-By 2 Power OFF 3 NOTE If the Indicating lamp is OFF, the Power Button on the Remote Control will not operate. Please make sure 1 that the power cord is plugged to the AC outlet. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
12
Quick Setup Guide
Perform the following steps to quickly setup your new
Hitachi LCD Television Set.
1. ANTENNA CONNECTION
Unless your LCD Television is connected to a cable TV system or
to a centralized antenna system, a good outdoor color TV antenna
is recommended for best performance. However, if you are located
in an exceptionally good signal area that is free from interference
and multiple image ghosts, an indoor antenna may be sufficient.
a).
VHF (75-Ohm) antenna/CATV (Cable TV)
When using a 75-Ohm coaxial cable system, connect the CATV coaxial
cable to the AIR/CABLE (75-Ohm) terminal. Or if you have an antenna,
connect the coaxial cable to the same AIR/CABLE terminal.
To outdoor Antenna
or
Cable TV (CATV)
System
To Air/Cable
Terminal
b). VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor antenna, connect
the VHF or UHF antenna leads to screws of the VHF or UHF adapter.
Plug the adapter into the TV Air/Cable terminal on the TV.
To outdoor VHF or
UHF Antenna
To Air/Cable-
Terminal
c).
When both VHF and UHF antennas are connected
Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial cable is recommended.
NOTE
Rear Panel Jack
a).
Connect the power cord to your TV set and secure it with the
AC Wire Clamp (see page 7)
.
AC Wire Clamp
a).
Connect the power cord to the AC wall outlet .
Attach an optional antenna cable mixer to the TV Air/Cable terminal
and connect the cables to the antenna mixer. Consult your dealer
or service store for the antenna mixer.
To outdoor antenna
or CATV system
To UHF antenna
Antenna Mixer
Air/Cable
b). The Indicating Lamp will light red (Standby mode) and then
light blue (picture is shown).
Indicating
Lamp
2. CONNECT YOUR NEW HITACHI LCD TV TO THE POWER SOURCE
3. POWER ON/OFF YOUR NEW HITACHI LCD TV
Press the POWER button on the Remote Control or the POWER
button on the Side Control Panel to power on/off the LCD TV.
or
RGB
RGB
Air/Cable
For Stand-By
Power OFF
If the Indicating lamp is OFF, the Power Button on the
Remote Control will not operate. Please make sure
that the power cord is plugged to the AC outlet.
NOTE