Hotpoint RGB528PENBB Owners Manual - Page 34

Electrical Connections, Cont., Openings, Light

Get Hotpoint RGB528PENBB - 30 Inch Gas Range PDF manuals and user guides View all Hotpoint RGB528PENBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Installation instructions [] ELECTRICAL CONNECTIONS (cont.) When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established. [] Usage Situations where Appliance Power Cord will be Disconnected Frequently. Do not use an adapter plug in these situations because disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal. The customer should have the 2-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified electrician before using the appliance. The installation of appliances designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard for Manufactured Home Installations, latest edition (Manufactured Home Sites, Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In Canada, mobile home installation must be in accordance with the current CAN/CSA Z240/MH Mobile Home Installation Code. Electric Disconnect * Locate disconnect plug on the range back. Pinch sides of connector and pull out of range back. [] SEAL THE OPENINGS Seal any openings in the wall behind the range and in the floor under the range when hookups are completed. [] LIGHT THE PILOTS (For models equipped with standing pilots. If the range is an electric ignition model, the burners are ignited by electric ignition which eliminates the need for standing pilot lights.) The range should be installed in its permanent position before any pilots are lit or adjusted. CAUTION - Make sure the surface burner control knobs are in the OFF position before attempting to light the pilots. [] Light the Surface Burner Pilots 1. Raise the cooktop. 2. Light both pilots with a match. 3. To avoid pilot outage, use caution when closing cooktop after lighting pilots. NOTE: Do not leave standing pilot lit in a newly constructed or remodeled home or apartment that will be unoccupied for more than a month. Each pilot flame was adjusted at the factory to be approximately 5/16" tall. A tinge of yellow appearing at the upper tip is normal. If you find pilot adjustment is necessary, follow instructions in Step B. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Installation
instructions
[]
ELECTRICAL CONNECTIONS
(cont.)
[]
When
disconnecting
the
power
cord
from
the
adapter,
always
hold
the
adapter
with
one
hand.
If this
is not
done,
the
adapter
ground
terminal
is very
likely
to
break
with
repeated
use.
Should
this
happen,
DO
NOT
USE
the
appliance
until
a proper
ground
has again
been
established.
Usage
Situations
where
Appliance
Power
Cord
will
be Disconnected
Frequently.
Do
not
use an adapter
plug
in
these
situations
because
disconnecting
of
the
power
cord
places
undue
strain
on the
adapter
and
leads
to
eventual
failure
of the
adapter
ground
terminal.
The
customer
should
have
the
2-prong
wall
receptacle
replaced
with
a three-prong
(grounding)
receptacle
by
a qualified
electrician
before
using
the
appliance.
The
installation
of
appliances
designed
for
mobile
home
installation
must
conform
with
the
Manufactured
Home
Construction
and
Safety
Standard,
Title
24 CFR, Part
3280
(formerly
the
Federal
Standard
for
Mobile
Home
Construction
and
Safety,
Title
24, HUD,
Part
280)
or,
when
such
standard
is not
applicable,
the
Standard
for
Manufactured
Home
Installations,
latest
edition
(Manufactured
Home
Sites,
Communities
and
Set-Ups),
ANSI
A225.1,
latest
edition,
or with
local
codes.
In Canada,
mobile
home
installation
must
be in accordance
with
the
current
CAN/CSA
Z240/MH
Mobile
Home
Installation
Code.
Electric
Disconnect
*
Locate
disconnect
plug
on the
range
back.
Pinch
sides
of
connector
and
pull
out
of
range
back.
[]
SEAL
THE
OPENINGS
Seal
any
openings
in the
wall
behind
the
range
and
in the
floor
under
the
range
when
hookups
are
completed.
[]
LIGHT
THE PILOTS
(For
models
equipped
with
standing
pilots.
If the
range
is an
electric
ignition
model,
the
burners
are
ignited
by electric
ignition
which
eliminates
the
need
for
standing
pilot
lights.)
The
range
should
be
installed
in its
permanent
position
before
any
pilots
are
lit
or adjusted.
CAUTION
-
Make
sure
the
surface
burner
control
knobs
are
in the
OFF position
before
attempting
to
light
the
pilots.
[]
Light
the
Surface
Burner
Pilots
1. Raise
the
cooktop.
2. Light
both
pilots
with
a match.
3. To avoid
pilot
outage,
use caution
when
closing
cooktop
after
lighting
pilots.
NOTE:
Do
not
leave
standing
pilot
lit
in
a newly
constructed
or
remodeled
home
or
apartment
that
will
be unoccupied
for
more
than
a month.
Each
pilot
flame
was
adjusted
at the
factory
to
be approximately
5/16"
tall.
A tinge
of yellow
appearing
at the
upper
tip
is normal.
If you
find
pilot
adjustment
is necessary,
follow
instructions
in Step
B.
34