IBM 8487 User Manual - Page 59

cover on and Removing and installing the support bracket

Get IBM 8487 - eServer xSeries 206 PDF manuals and user guides
UPC - 000435687531
View all IBM 8487 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Statement 2 CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations. Complete the following steps to replace the battery: 1. Read "Installation guidelines" on page 23 and the safety information beginning at "Safety information" on page 107. 2. Follow any special handling and installation instructions supplied with the replacement battery. 3. Turn off the server and all attached devices. 4. Disconnect all power cords; then, disconnect all external cables. 5. Remove the side cover and frame-support bracket (see "Removing the side cover" on page 26 and "Removing and installing the support bracket" on page 28). 6. Remove any adapters that impede access to the battery. 7. Remove the battery: a. Use a fingernail to press the top of the battery clip away from the battery. The battery pops up when released. b. Use your thumb and index finger to lift the battery from the socket. 8. Insert the new battery: a. Tilt the battery so that you can insert it into the socket on the side opposite the battery clip. b. Press the battery down into the socket until it clicks into place. Make sure the battery clip holds the battery securely. Chapter 4. Installing options 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type made
by the same manufacturer. The battery contains lithium and can explode if not
properly used, handled, or disposed of.
Do not:
v
Throw or immerse into water
v
Heat to more than 100°C (212°F)
v
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Complete the following steps to replace the battery:
1.
Read “Installation guidelines” on page 23 and the safety information beginning
at “Safety information” on page 107.
2.
Follow any special handling and installation instructions supplied with the
replacement battery.
3.
Turn off the server and all attached devices.
4.
Disconnect all power cords; then, disconnect all external cables.
5.
Remove the side cover and frame-support bracket (see “Removing the side
cover” on page 26 and “Removing and installing the support bracket” on page
28).
6.
Remove any adapters that impede access to the battery.
7.
Remove the battery:
a.
Use a fingernail to press the top of the battery clip away from the battery.
The battery pops up when released.
b.
Use your thumb and index finger to lift the battery from the socket.
8.
Insert the new battery:
a.
Tilt the battery so that you can insert it into the socket on the side opposite
the battery clip.
b.
Press the battery down into the socket until it clicks into place. Make sure
the battery clip holds the battery securely.
Chapter 4. Installing options
49