IBM 8487 User Manual - Page 71

SCSI mini-PCI-X adapter, Remove the cover and support bracket seeRemoving the side cover

Get IBM 8487 - eServer xSeries 206 PDF manuals and user guides
UPC - 000435687531
View all IBM 8487 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

SCSI mini-PCI-X adapter Note: v Read "Installation guidelines" on page 23. v Read the safety notices at "Safety information" on page 107. v Read "Handling static-sensitive devices" on page 24. Complete the following steps to remove the SCSI mini-PCI-X adapter: 1. Turn off the server and attached devices; then, disconnect all power cords and external cables. Note: It may be easier to perform this procedure if the server is laying on its side. 2. Remove the cover and support bracket (see"Removing the side cover" on page 26 and "Removing and installing the support bracket" on page 28). 3. Remove any adapters (see "Installing an adapter" on page 44) that impede access to the SCSI mini-PCI-X adapter. 4. Disconnect the cable from the SCSI mini-PCI-X adapter. Note: The illustrations in this document might differ slightly from your hardware. Note: The plastic stand-offs are shown detached in the illustration above. 5. Using pliers, gently pinch the top of each of the two plastic stand-offs that secure the adapter to the system board; then, place a finger under the adapter near each stand-off and pull up until the adapter disengages from the stand-off. Chapter 6. Field replaceable units 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
SCSI mini-PCI-X adapter
Note:
v
Read “Installation guidelines” on page 23.
v
Read the safety notices at “Safety information” on page 107.
v
Read “Handling static-sensitive devices” on page 24.
Complete the following steps to remove the SCSI mini-PCI-X adapter:
1.
Turn off the server and attached devices; then, disconnect all power cords and
external cables.
Note:
It may be easier to perform this procedure if the server is laying on its
side.
2.
Remove the cover and support bracket (see“Removing the side cover” on page
26 and “Removing and installing the support bracket” on page 28).
3.
Remove any adapters (see “Installing an adapter” on page 44) that impede
access to the SCSI mini-PCI-X adapter.
4.
Disconnect the cable from the SCSI mini-PCI-X adapter.
Note:
The illustrations in this document might differ slightly from your hardware.
Note:
The plastic stand-offs are shown detached in the illustration above.
5.
Using pliers, gently pinch the top of each of the two plastic stand-offs that
secure the adapter to the system board; then, place a finger under the adapter
near each stand-off and pull up until the adapter disengages from the stand-off.
Chapter 6. Field replaceable units
61