IBM 8649 Hardware Maintenance Manual - Page 61

Installing, 25-inch, removable-media, drive

Get IBM 8649 - Eserver xSeries 225 PDF manuals and user guides
UPC - 000435133427
View all IBM 8649 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Installing a 5.25-inch removable-media drive Your server comes with one integrated drive electronics (IDE) CD-ROM drive. The CD-ROM drive bay supports a 5.25-inch, half-high, removable-media drive. You can install an additional 5.25-inch, half-high, removable-media drive in bay 2. A three-drop power cable comes with your server. Use this cable to connect power to the removable-media drives. Check the instructions that come with the drive to see if you need to set any switches or jumpers on the drive. If you are installing a SCSI device, be sure to set the SCSI ID for that device. Verify that you have all the cables and other equipment specified in the documentation that comes with the drive. Complete the following steps to install a removable-media drive in bay 2 (see "Internal drive bays" on page 44): 1. Review the safety information beginning on page 129 and "Installation guidelines" on page 33. 2. Turn off the server and all attached devices. 3. Disconnect all power cords; then, disconnect all external cables. 4. Remove the side cover (see "Removing the side cover" on page 36). 5. Remove the bezel (see "Removing the bezel" on page 37). 6. Remove the support bracket (see "Removing and installing the support bracket" on page 38). 7. Use a screwdriver to pry the filler panel and EMC shield away from the server. Note: If you are installing a drive that contains a laser, observe the following safety precaution. Chapter 4. Installing options 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Installing
a
5.25-inch
removable-media
drive
Your
server
comes
with
one
integrated
drive
electronics
(IDE)
CD-ROM
drive.
The
CD-ROM
drive
bay
supports
a
5.25-inch,
half-high,
removable-media
drive.
You
can
install
an
additional
5.25-inch,
half-high,
removable-media
drive
in
bay
2.
A
three-drop
power
cable
comes
with
your
server.
Use
this
cable
to
connect
power
to
the
removable-media
drives.
Check
the
instructions
that
come
with
the
drive
to
see
if
you
need
to
set
any
switches
or
jumpers
on
the
drive.
If
you
are
installing
a
SCSI
device,
be
sure
to
set
the
SCSI
ID
for
that
device.
Verify
that
you
have
all
the
cables
and
other
equipment
specified
in
the
documentation
that
comes
with
the
drive.
Complete
the
following
steps
to
install
a
removable-media
drive
in
bay
2
(see
“Internal
drive
bays”
on
page
44):
1.
Review
the
safety
information
beginning
on
page
129
and
“Installation
guidelines”
on
page
33.
2.
Turn
off
the
server
and
all
attached
devices.
3.
Disconnect
all
power
cords;
then,
disconnect
all
external
cables.
4.
Remove
the
side
cover
(see
“Removing
the
side
cover”
on
page
36).
5.
Remove
the
bezel
(see
“Removing
the
bezel”
on
page
37).
6.
Remove
the
support
bracket
(see
“Removing
and
installing
the
support
bracket”
on
page
38).
7.
Use
a
screwdriver
to
pry
the
filler
panel
and
EMC
shield
away
from
the
server.
Note:
If
you
are
installing
a
drive
that
contains
a
laser,
observe
the
following
safety
precaution.
Chapter
4.
Installing
options
51