IBM 8649 Hardware Maintenance Manual - Page 76

Completing, option, installation, Replacing, bezel

Get IBM 8649 - Eserver xSeries 225 PDF manuals and user guides
UPC - 000435133427
View all IBM 8649 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Completing the option installation To complete installation of an option, you must reinstall the bezel, reinstall the server cover, reconnect all the cables that you disconnected earlier and, for certain options, run the Configuration/Setup Utility program. Follow the instructions in this section. Attention: For proper cooling and airflow, replace the server cover before or shortly after turning on the server. Operating the server for extended periods of time (over 30 minutes) with the server cover removed might damage server components. Note: If you have just plugged the power cords of your server into electrical outlets, you will have to wait approximately 20 seconds before pressing the power-control button. Replacing the bezel The following illustration shows how to install the bezel on the server. Complete the following steps to replace the bezel: 1. Insert the two tabs on the bottom of the bezel into the matching holes on the server chassis. 2. Push the top of the bezel toward the server until the two tabs at the top of the bezel snap into place. 3. For hot-swap hard disk drive models, make sure the side cover is unlocked; then, insert the hot-swap lock bar into the slots on the bezel and rotate it to the locked position. The hot-swap lock bar locks when you lock the side cover key lock. 66 IBM xSeries 225 Types 8649: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Completing
the
option
installation
To
complete
installation
of
an
option,
you
must
reinstall
the
bezel,
reinstall
the
server
cover,
reconnect
all
the
cables
that
you
disconnected
earlier
and,
for
certain
options,
run
the
Configuration/Setup
Utility
program.
Follow
the
instructions
in
this
section.
Attention:
For
proper
cooling
and
airflow,
replace
the
server
cover
before
or
shortly
after
turning
on
the
server.
Operating
the
server
for
extended
periods
of
time
(over
30
minutes)
with
the
server
cover
removed
might
damage
server
components.
Note:
If
you
have
just
plugged
the
power
cords
of
your
server
into
electrical
outlets,
you
will
have
to
wait
approximately
20
seconds
before
pressing
the
power-control
button.
Replacing
the
bezel
The
following
illustration
shows
how
to
install
the
bezel
on
the
server.
Complete
the
following
steps
to
replace
the
bezel:
1.
Insert
the
two
tabs
on
the
bottom
of
the
bezel
into
the
matching
holes
on
the
server
chassis.
2.
Push
the
top
of
the
bezel
toward
the
server
until
the
two
tabs
at
the
top
of
the
bezel
snap
into
place.
3.
For
hot-swap
hard
disk
drive
models,
make
sure
the
side
cover
is
unlocked;
then,
insert
the
hot-swap
lock
bar
into
the
slots
on
the
bezel
and
rotate
it
to
the
locked
position.
The
hot-swap
lock
bar
locks
when
you
lock
the
side
cover
key
lock.
66
IBM
xSeries
225
Types
8649:
Hardware
Maintenance
Manual
and
Troubleshooting
Guide