IBM 867282X Maintenance Manual - Page 32

Ethernet controller messages, Novell NetWare or IntraNetWare system ODI driver teaming messages

Get IBM 867282X - Eserver xSeries 300 PDF manuals and user guides
UPC - 087944650966
View all IBM 867282X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Ethernet controller messages The integrated Ethernet controller might display messages from the following device drivers: v ™ Novell NetWare or IntraNetWare system open data-link interface (ODI) v Network driver interface specification (NDIS) adapter for level 4.0 (Windows NT) Novell NetWare or IntraNetWare system ODI driver teaming messages This section provides explanations of the error messages for the Novell NetWare or IntraNetWare system ODI driver, and suggested actions to resolve each problem. Table 3. NetWare driver messages for the Ethernet controller Message Description Couldn't allocate resources. Explanation: An unknown error has occurred when trying to allocate needed resources for the AFT Module. Action: v Check the server configuration. v Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, run the diagnostic programs. AFT group for primary adapter in slot nnn already exists. Explanation: An attempt was made to rebind an adapter already in an AFT group. Action: Check the AFT slot numbers for existing AFT teams. Error locating device control Explanation: The bind command was entered prior to table (DCT) addresses in loading the device driver. The device driver must be loaded internal table. Make sure that after loading AFT.NLM, but before any bind command can you have loaded LAN be issued. Action: Load the driver for the supported drivers after loading adapter and try loading the AFT module again. AFT.NLM. Insufficient number of arguments specified. Duplicate slot numbers detected. Explanation: The appropriate or expected number of parameters was not entered in a command. Action: Check the parameters required for the given command. Explanation: An attempt has been made to bind the same slot number more than once. Action: Check the slot numbers entered during the bind. Adapter slot numbers must be valid and unique. 'xxx' is not supported for AFT team. Explanation: A bind command has been issued for adapters not supported by AFT.NLM. Action: Make sure that you attempt to bind only adapters supported by AFT.NLM. Primary and Secondary adapters do not match. AFT group is not created. Explanation: A bind command was entered for an adapter team that is a combination of server and client adapters. An AFT team must be a grouping of the same classification of adapter. Action: Verify that all the adapters bound in a team are of the same classification. Requested number of Secondary cards are not found. Explanation: The number of adapters specified in the bind command could not be located. Action: Verify the numbers and slot locations of the adapters to be bound. 24 Hardware Maintenance Manual: xSeries 300

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Ethernet controller messages
The integrated Ethernet controller might display messages from the following
device drivers:
v
Novell NetWare
™
or IntraNetWare system open data-link interface (ODI)
v
Network driver interface specification (NDIS) adapter for level 4.0 (Windows
NT)
Novell NetWare or IntraNetWare system ODI driver teaming
messages
This section provides explanations of the error messages for the Novell NetWare or
IntraNetWare system ODI driver, and suggested actions to resolve each problem.
Table 3. NetWare driver messages for the Ethernet controller
Message
Description
Couldn
’
t allocate resources.
Explanation:
An unknown error has occurred when trying
to allocate needed resources for the AFT Module.
Action:
v
Check the server configuration.
v
Verify that the Ethernet controller is enabled. If the
Ethernet controller is enabled, run the diagnostic
programs.
AFT group for primary
adapter in slot
nnn
already
exists.
Explanation:
An attempt was made to rebind an adapter
already in an AFT group.
Action:
Check the AFT slot
numbers for existing AFT teams.
Error locating device control
table (DCT) addresses in
internal table. Make sure that
you have loaded LAN
drivers after loading
AFT.NLM.
Explanation:
The bind command was entered prior to
loading the device driver. The device driver must be loaded
after loading AFT.NLM, but before any bind command can
be issued.
Action:
Load the driver for the supported
adapter and try loading the AFT module again.
Insufficient number of
arguments specified.
Explanation:
The appropriate or expected number of
parameters was not entered in a command.
Action:
Check
the parameters required for the given command.
Duplicate slot numbers
detected.
Explanation:
An attempt has been made to bind the same
slot number more than once.
Action:
Check the slot
numbers entered during the bind. Adapter slot numbers
must be valid and unique.
’
xxx
’
is not supported for
AFT team.
Explanation:
A bind command has been issued for adapters
not supported by AFT.NLM.
Action:
Make sure that you
attempt to bind only adapters supported by AFT.NLM.
Primary and Secondary
adapters do not match. AFT
group is not created.
Explanation:
A bind command was entered for an adapter
team that is a combination of server and client adapters. An
AFT team must be a grouping of the same classification of
adapter.
Action:
Verify that all the adapters bound in a
team are of the same classification.
Requested number of
Secondary cards are not
found.
Explanation:
The number of adapters specified in the bind
command could not be located.
Action:
Verify the numbers
and slot locations of the adapters to be bound.
24
Hardware Maintenance Manual: xSeries 300