IBM 867282X Maintenance Manual - Page 64

Diskette/CD-ROM drive bracket

Get IBM 867282X - Eserver xSeries 300 PDF manuals and user guides
UPC - 087944650966
View all IBM 867282X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Diskette/CD-ROM drive bracket Slim adapter board Diskette drive retaining wire Metal tab Diskette drive Bracket CD-ROM drive retaining wire CD-ROM drive To remove the diskette/CD-ROM drive bracket: Note: Read"Safety information" on page 75 and "Before you begin" on page 36. 1. Remove the diskette/CD-ROM drive. See "Diskette/CD-ROM drives" on page 55. 2. Remove the diskette drive: a. Remove the diskette drive retaining wire by releasing it from the metal tab and removing it from the holes, and put it in a safe place. b. Lift the diskette drive up on one side until it will separates from the bracket. c. Diskette drive cable: 1) The diskette drive cable is removed by gently pulling the cable up until it is released from the connector. 2) To replace the diskette drive cable, pull up on the connector latch until it is unlocked; then, insert the end of the cable into the connector and gently push down on the connector latch until it clicks into place. 3. Remove the CD-ROM drive: a. Remove the CD-ROM drive retaining wire by releasing it from the metal tab and removing it from the holes, and put it in a safe place. b. Gently loosen the connector of the slim adapter board from the CD-ROM drive connector until it pulls free; slide the slim adapter board down until it clears the notches on the bracket and remove it. c. Slide the bracket toward the rear and remove it. 56 Hardware Maintenance Manual: xSeries 300

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Diskette/CD-ROM drive bracket
Diskette drive
Slim adapter board
Bracket
CD-ROM drive
CD-ROM drive
retaining wire
Diskette drive
retaining wire
Metal tab
To remove the diskette/CD-ROM drive bracket:
Note:
Read
“
Safety information
”
on page 75 and
“
Before you begin
”
on page 36.
1.
Remove the diskette/CD-ROM drive. See
“
Diskette/CD-ROM drives
”
on
page 55.
2.
Remove the diskette drive:
a.
Remove the diskette drive retaining wire by releasing it from the metal tab
and removing it from the holes, and put it in a safe place.
b.
Lift the diskette drive up on one side until it will separates from the
bracket.
c.
Diskette drive cable:
1)
The diskette drive cable is removed by gently pulling the cable up until
it is released from the connector.
2)
To replace the diskette drive cable, pull up on the connector latch until it
is unlocked; then, insert the end of the cable into the connector and
gently push down on the connector latch until it clicks into place.
3.
Remove the CD-ROM drive:
a.
Remove the CD-ROM drive retaining wire by releasing it from the metal tab
and removing it from the holes, and put it in a safe place.
b.
Gently loosen the connector of the slim adapter board from the CD-ROM
drive connector until it pulls free; slide the slim adapter board down until it
clears the notches on the bracket and remove it.
c.
Slide the bracket toward the rear and remove it.
56
Hardware Maintenance Manual: xSeries 300