IBM 867282X Maintenance Manual - Page 61

Installing the cover, with your server documentation for instructions.

Get IBM 867282X - Eserver xSeries 300 PDF manuals and user guides
UPC - 087944650966
View all IBM 867282X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Installing the cover Complete the following steps to install the server cover: 1. Install the cover by placing it into position and sliding it forward. Make sure that the cover engages the tabs at the front and rear of the server. Attention: Before sliding the cover forward, place the cover over 80% of the box, to ensure that cables are covered, and make sure that all of the tabs on the cover will engage the ledge at the front of the server properly. If all the tabs do not engage the ledge properly, it will be extremely difficult to remove the cover later. Screws 2. Install the screws to secure the cover as shown. 3. Install the server in the rack. See the ″Rack installation instuctions″ included with your server documentation for instructions. 4. Connect the power cord and all external cables to the server, and then plug the power cords into properly grounded electrical outlets. See "Working with cables" on page 54 for connector locations. Chapter 5. Installing Options 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Installing the cover
Complete the following steps to install the server cover:
1.
Install the cover by placing it into position and sliding it forward.
Make sure
that the cover engages the tabs at the front and rear of the server.
Attention:
Before sliding the cover forward, place the cover over 80% of the
box, to ensure that cables are covered, and make sure that all of the tabs on the
cover will engage the ledge at the front of the server properly. If all the tabs do
not engage the ledge properly, it will be extremely difficult to remove the cover
later.
Screws
2.
Install the screws to secure the cover as shown.
3.
Install the server in the rack. See the
″
Rack installation instuctions
″
included
with your server documentation for instructions.
4.
Connect the power cord and all external cables to the server, and then plug the
power cords into properly grounded electrical outlets. See
“
Working with
cables
”
on page 54 for connector locations.
Chapter 5. Installing Options
53