Home » Intel Manuals » Processors » Intel QX9770 » Manual Viewer

Intel QX9770 Design Guidelines - Page 18

TCONTROL, Intel, Quiet System, Technology Intel

UPC - 735858197564

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

LGA775 Socket Heatsink Loading temperature. Using the example in Figure 3 for a processor dissipating 110W the maximum case temperature is 52.2°C. See the datasheet for the thermal profile. Figure 3. Example Thermal Profile 2.2.3 TCONTROL TCONTROL defines the maximum operating temperature for the digital thermal sensor when the thermal solution fan speed is being controlled by the digital thermal sensor. The TCONTROL parameter defines a very specific processor operating region where fan speed can be reduced. This allows the system integrator a method to reduce the acoustic noise of the processor cooling solution, while maintaining compliance to the processor thermal specification. Note: The TCONTROL value for the processor is relative to the Thermal Control Circuit (TCC) activation set point which will be seen as 0 via the digital thermometer. As a result the TCONTROL value will always be a negative number. See Chapter 4 for the discussion the thermal management logic and features and Chapter 6 on Intel® Quiet System Technology (Intel® QST). The value of TCONTROL is driven by a number of factors. One of the most significant of these is the processor idle power. As a result a processor with a high (closer to 0) TCONTROL will dissipate more power than a part with lower value (farther from 0, e.g. more negative number) of TCONTROL when running the same application. The value of TCONTROL is calculated such that regardless of the individual processor's TCONTROL value the thermal solution should perform similarly. The higher power of some parts is offset by a higher value of TCONTROL in such a way that they should behave similarly in the acoustic performance. 18 Thermal and Mechanical Design Guidelines

Section	Page
1 Introduction	9
1.1 Document Goals and Scope	9
1.1.1 Importance of Thermal Management	9
1.1.2 Document Goals	9
1.1.3 Document Scope	10
1.2 References	11
1.3 Definition of Terms	11
2 Processor Thermal/Mechanical Information	13
2.1 Mechanical Requirements	13
2.1.1 Processor Package	13
2.1.2 Heatsink Attach	15
2.1.2.1 General Guidelines	15
2.1.2.2 The Pump Assembly Clip Load Requirement	15
2.1.2.3 Additional Guidelines	16
2.2 Thermal Requirements	16
2.2.1 Processor Case Temperature	16
2.2.2 Thermal Profile	17
2.2.3 TCONTROL	18
2.3 Heatsink Design Considerations	19
2.3.1 Heatsink Size	20
2.3.2 Package IHS Flatness	20
2.3.3 Thermal Interface Material	21
2.4 System Thermal Solution Considerations	21
2.4.1 Chassis Thermal Design Capabilities	21
2.4.2 Improving Chassis Thermal Performance	21
2.4.3 Summary	22
2.5 System Integration Considerations	22
3 Thermal Metrology	23
3.1 Characterizing Cooling Performance Requirements	23
3.1.1 Example	25
3.2 Processor Thermal Solution Performance Assessment	26
3.3 Local Ambient Temperature Measurement Guidelines	26
3.4 Processor Case Temperature Measurement Guidelines	29
4 Thermal Management Logic and Thermal Monitor Feature	31
4.1 Processor Power Dissipation	31
4.2 Thermal Monitor Implementation	31
4.2.1 PROCHOT# Signal	32
4.2.2 Thermal Control Circuit	32
4.2.3 Thermal Monitor 2	33
4.2.4 Operation and Configuration	34
4.2.5 On-Demand Mode	35
4.2.6 System Considerations	35
4.2.7 Operating System and Application Software Considerations	36
4.2.8 THERMTRIP# Signal	36
4.2.9 Cooling System Failure Warning	36
4.2.10 Digital Thermal Sensor	37
4.2.11 Platform Environmental Control Interface (PECI)	38
5 Intel Thermal/Mechanical Reference Design Information	39
5.1 Validation Results for the ATX Reference Design	39
5.1.1 Heatsink Performance	40
5.1.2 Acoustics	40
5.1.3 Altitude	41
5.1.4 Reference Heatsink Thermal Validation	41
5.1.5 Fan Motor Performance	42
5.1.6 Pump Motor Performance	43
5.2 Environmental Reliability Testing	44
5.2.1 Structural Reliability Testing	44
5.2.1.1 Random Vibration Test Procedure	44
5.2.1.2 Shock Test Procedure	45
5.2.2 Power Cycling	46
5.2.3 Reliability Testing	46
5.2.3.1 Tubing Material Selection	48
5.2.3.2 Reservoir Sizing	48
5.2.3.3 Reliability Test Results	50
5.2.4 Recommended BIOS/CPU/Memory Test Procedures	51
5.3 Material and Recycling Requirements	52
5.4 Safety Requirements	52
5.5 Geometric Envelope for Intel Reference ATX Thermal Mechanical Design	52
5.6 Reference Attach Mechanism	54
5.7 Socket and Voltage Regulation Cooling Strategy	55
6 Intel® Quiet System Technology (Intel® QST)	57
6.1 Intel® Quiet System Technology Algorithm	57
6.1.1 Output Weighting Matrix	58
6.1.2 Proportional-Integral-Derivative (PID)	58
6.2 Board and System Implementation of Intel® Quiet System Technology	60
6.3 Intel® QST Configuration & Tuning	62