Home » Intel Manuals » Processors » Intel QX9770 » Manual Viewer

Intel QX9770 Design Guidelines - Page 78

Supporting Test Equipment, Description, Part Number, Measurement and Output

UPC - 735858197564

Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Case Temperature Reference Metrology D.2 Supporting Test Equipment To apply the reference thermocouple attach procedure, it is recommended to use the equipment (or equivalent) given in the table below. Item Description Part Number Measurement and Output Microscope DMM Thermal Meter Olympus* Light microscope or equivalent SZ-40 Digital Multi Meter for resistance measurement Fluke 79 Series Hand held thermocouple meter Multiple Vendors Solder Station (see note 1 for ordering information) Heater Block Heater Transformer Heater assembly to reflow solder on IHS WATLOW120V 150W Firerod Superior Powerstat transformer Miscellaneous Hardware 30330 0212G G1A38L12 05F857 Solder Flux Loctite* 498 Adhesive Adhesive Accelerator Kapton* Tape Thermocouple Indium Corp. of America Alloy 57BI / 42SN / 1AG 0.010 Diameter Indium Corp. of America Super glue w/thermal characteristics Loctite* 7452 for fast glue curing For holding thermocouple in place Omega *,36 gauge, "T" Type (see note 2 for ordering information) Calibration and Control 52124 5RMA 49850 18490 Not Available OSK2K1280/5SR TC-TT-T-36-72 Ice Point Cell Hot Point Cell Omega*, stable 0 ºC temperature source for calibration and offset Omega *, temperature source to control and understand meter slope gain TRCIII CL950-A-110 NOTES: 1. The Solder Station consisting of the Heater Block, Heater, Press and Transformer are available from Jemelco Engineering 480-804-9514 2. This part number is a custom part with the specified insulation trimming and packaging requirements necessary for quality thermocouple attachment, See Figure 31. Order from Omega Anthony Alvarez, Direct phone (203) 359-7671, Direct fax (203) 9687142, E-Mail: [email protected] 78 Thermal and Mechanical Design Guidelines

Section	Page
1 Introduction	9
1.1 Document Goals and Scope	9
1.1.1 Importance of Thermal Management	9
1.1.2 Document Goals	9
1.1.3 Document Scope	10
1.2 References	11
1.3 Definition of Terms	11
2 Processor Thermal/Mechanical Information	13
2.1 Mechanical Requirements	13
2.1.1 Processor Package	13
2.1.2 Heatsink Attach	15
2.1.2.1 General Guidelines	15
2.1.2.2 The Pump Assembly Clip Load Requirement	15
2.1.2.3 Additional Guidelines	16
2.2 Thermal Requirements	16
2.2.1 Processor Case Temperature	16
2.2.2 Thermal Profile	17
2.2.3 TCONTROL	18
2.3 Heatsink Design Considerations	19
2.3.1 Heatsink Size	20
2.3.2 Package IHS Flatness	20
2.3.3 Thermal Interface Material	21
2.4 System Thermal Solution Considerations	21
2.4.1 Chassis Thermal Design Capabilities	21
2.4.2 Improving Chassis Thermal Performance	21
2.4.3 Summary	22
2.5 System Integration Considerations	22
3 Thermal Metrology	23
3.1 Characterizing Cooling Performance Requirements	23
3.1.1 Example	25
3.2 Processor Thermal Solution Performance Assessment	26
3.3 Local Ambient Temperature Measurement Guidelines	26
3.4 Processor Case Temperature Measurement Guidelines	29
4 Thermal Management Logic and Thermal Monitor Feature	31
4.1 Processor Power Dissipation	31
4.2 Thermal Monitor Implementation	31
4.2.1 PROCHOT# Signal	32
4.2.2 Thermal Control Circuit	32
4.2.3 Thermal Monitor 2	33
4.2.4 Operation and Configuration	34
4.2.5 On-Demand Mode	35
4.2.6 System Considerations	35
4.2.7 Operating System and Application Software Considerations	36
4.2.8 THERMTRIP# Signal	36
4.2.9 Cooling System Failure Warning	36
4.2.10 Digital Thermal Sensor	37
4.2.11 Platform Environmental Control Interface (PECI)	38
5 Intel Thermal/Mechanical Reference Design Information	39
5.1 Validation Results for the ATX Reference Design	39
5.1.1 Heatsink Performance	40
5.1.2 Acoustics	40
5.1.3 Altitude	41
5.1.4 Reference Heatsink Thermal Validation	41
5.1.5 Fan Motor Performance	42
5.1.6 Pump Motor Performance	43
5.2 Environmental Reliability Testing	44
5.2.1 Structural Reliability Testing	44
5.2.1.1 Random Vibration Test Procedure	44
5.2.1.2 Shock Test Procedure	45
5.2.2 Power Cycling	46
5.2.3 Reliability Testing	46
5.2.3.1 Tubing Material Selection	48
5.2.3.2 Reservoir Sizing	48
5.2.3.3 Reliability Test Results	50
5.2.4 Recommended BIOS/CPU/Memory Test Procedures	51
5.3 Material and Recycling Requirements	52
5.4 Safety Requirements	52
5.5 Geometric Envelope for Intel Reference ATX Thermal Mechanical Design	52
5.6 Reference Attach Mechanism	54
5.7 Socket and Voltage Regulation Cooling Strategy	55
6 Intel® Quiet System Technology (Intel® QST)	57
6.1 Intel® Quiet System Technology Algorithm	57
6.1.1 Output Weighting Matrix	58
6.1.2 Proportional-Integral-Derivative (PID)	58
6.2 Board and System Implementation of Intel® Quiet System Technology	60
6.3 Intel® QST Configuration & Tuning	62