Intel SC5600BASE Service Guide - Page 58

Installing PCI Add-in Boards

Get Intel SC5600BASE PDF manuals and user guides View all Intel SC5600BASE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Hardware Installations and Upgrades 7. Firmly grab the PCI add-in board by its top edge or outer corners and remove from the expansion slot on the server board. Place the removed PCI add-in board in an anti-static protective wrapper. Close the back panel PCI add-in card retention device. 8. Remove additional PCI add-in boards as necessary. When done, reinstall the PCI add-in card retainer and close the PCI add-in card retention device(s). 9. Install the front bezel. For instructions, see "Removing and Installing the Front Bezel." 10. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 11. Plug all peripheral devices and the AC power cable into the server. 12. Power up the server. Installing PCI Add-in Board(s) CAUTIONS Before installing any add-in boards, you may want to install an operating system. Do not overload the server board by installing add-in boards that draw excessive current. Add-in boards can be extremely sensitive to ESD and always require careful handling. After removing the board from its protective wrapper, place it component side up on a grounded, static-free surface. Do not slide the board over any surface. When removing a full-length add-in card, you must pull back on the latch on the plastic card guide at the front of the chassis to release the card from the card guide. 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. If it is installed, remove the front bezel. For instructions, see "Removing and Installing the Front Bezel." 5. Press in on the two plastic tabs (see letter "A" in Figure 50) and remove the PCI add-in card retainer. Open the back panel PCI add-in card retention device (see letter "B") by pressing open from the inside of the chassis. Remove the PCI slot shield (see letter "C"), if it is not already removed, by pushing the shield out from the inside of the chassis. 44 Intel® Server Chassis SC5600 Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Hardware Installations and Upgrades
44
Intel®
Server Chassis SC5600 Service Guide
7.
Firmly grab the PCI add-in board by its top edge or outer corners and remove from the expansion slot on
the server board. Place the removed PCI add-in board in an anti-static protective wrapper. Close the back
panel PCI add-in card retention device.
8.
Remove additional PCI add-in boards as necessary. When done, reinstall the PCI add-in card retainer and
close the PCI add-in card retention device(s).
9.
Install the front bezel. For instructions, see “Removing and Installing the Front Bezel.”
10. Install the chassis cover. For instructions, see “Installing the Chassis Cover.”
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Installing PCI Add-in Board(s)
CAUTIONS
Before installing any add-in boards, you may want to install an operating system.
Do not overload the server board by installing add-in boards that draw excessive current.
Add-in boards can be extremely sensitive to ESD and always require careful handling. After removing
the board from its protective wrapper, place it component side up on a grounded, static-free surface.
Do not slide the board over any surface.
When removing a full-length add-in card, you must pull back on the latch on the plastic card guide at
the front of the chassis to release the card from the card guide.
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover.”
4.
If it is installed, remove the front bezel. For instructions, see “Removing and Installing the Front Bezel.”
5.
Press in on the two plastic tabs (see letter “A” in Figure 50) and remove the PCI add-in card retainer.
Open the back panel PCI add-in card retention device (see letter “B”) by pressing open from the inside of
the chassis. Remove the PCI slot shield (see letter “C”), if it is not already removed, by pushing the shield
out from the inside of the chassis.