Intel SC5600BASE Service Guide - Page 69

Installing and/or Removing a Server/Workstation, Board

Get Intel SC5600BASE PDF manuals and user guides View all Intel SC5600BASE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Hardware Installations and Upgrades 7. Disconnect the cables. 8. Install the control panel module into the chassis. 9. Reconnect the cables. 10. (Optional) Install the front bezel. For instructions, see "Removing and Installing the Front Bezel." 11. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 12. Plug all peripheral devices and the AC power cable into the server. 13. Power up the server. Installing and/or Removing a Server/Workstation Board / NOTE The server/Workstation board you can install in your chassis depends upon the chassis model. To install or remove a server board, do the following: 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. If it is installed, remove the front bezel assembly. For instructions, see "Removing the Bezel Assembly (Pedestal Only)." 5. Remove any PCI add-in boards that are present. For instructions, see "Removing PCI Add-in Board(s)." 6. Remove the air duct. For instructions, see "Removing the Air Duct." 7. If installing a server board, refer to the Service Guide and/or Quick Start User's Guide that shipped with your Intel® server/workstation board for installation instructions. Use the mounting screws, bumpers, and standoffs (if necessary) that came with your chassis to secure the server/workstation board to the chassis. Make sure the server/workstation board is properly seated and then tighten the screws firmly, starting with the screws at the center of the server/workstation board. Make cable connections per the instructions in the Intel® server/workstation board Service Guide and/or Quick Start User's Guide. 8. If removing a server board, disconnect all cables connected to the server board. 9. Remove the mounting screws, starting with the screws at the center of the server/workstation board. Remove the server board. 10. Re-install the air duct. For instructions, see "Installing the Air Duct" on page 32. 11. If needed, install any PCI Add-in boards. For instructions, see "Installing PCI Add-in Board(s)." 12. Re-install the front bezel assembly. For instructions, see "Installing the Front Bezel (Pedestal Only)." 13. Re-install the chassis cover. For instructions, see "Installing the Chassis Cover." 14. Plug all peripheral devices and the AC power cable into the server. 15. Power up the server. Intel® Server Chassis SC5600 Service Guide 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Hardware Installations and Upgrades
Intel®
Server
Chassis SC5600 Service Guide
55
7.
Disconnect the cables.
8.
Install the control panel module into the chassis.
9.
Reconnect the cables.
10. (Optional) Install the front bezel. For instructions, see “Removing and Installing the Front Bezel.”
11. Install the chassis cover. For instructions, see “Installing the Chassis Cover.”
12. Plug all peripheral devices and the AC power cable into the server.
13. Power up the server.
Installing and/or Removing a Server/Workstation
Board
/
NOTE
The server/Workstation board you can install in your chassis depends upon the chassis model.
To install or remove a server board, do the following:
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover.”
4.
If it is installed, remove the front bezel assembly. For instructions, see “Removing the Bezel Assembly
(Pedestal Only).”
5.
Remove any PCI add-in boards that are present. For instructions, see “Removing PCI Add-in Board(s).”
6.
Remove the air duct. For instructions, see “Removing the Air Duct.”
7.
If installing a server board, refer to the
Service Guide
and/or
Quick Start User’s Guide
that shipped with
your Intel
®
server/workstation board for installation instructions. Use the mounting screws, bumpers, and
standoffs (if necessary) that came with your chassis to secure the server/workstation board to the chassis.
Make sure the server/workstation board is properly seated and then tighten the screws firmly, starting with
the screws at the center of the server/workstation board. Make cable connections per the instructions in
the Intel
®
server/workstation board
Service Guide
and/or
Quick Start User’s Guide
.
8.
If removing a server board, disconnect all cables connected to the server board.
9.
Remove the mounting screws, starting with the screws at the center of the server/workstation board.
Remove the server board.
10. Re-install the air duct. For instructions, see “Installing the Air Duct” on page 32.
11. If needed, install any PCI Add-in boards. For instructions, see “Installing PCI Add-in Board(s).”
12. Re-install the front bezel assembly. For instructions, see “Installing the Front Bezel (Pedestal Only).”
13. Re-install the chassis cover. For instructions, see “Installing the Chassis Cover.”
14. Plug all peripheral devices and the AC power cable into the server.
15. Power up the server.