Invacare P9000XDT1818 Owners Manual - Page 33

Front Riggings

Get Invacare P9000XDT1818 PDF manuals and user guides View all Invacare P9000XDT1818 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

SECTION 6-FRONT RIGGINGS SECTION 6-FRONT RIGGINGS ƽ WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result. While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving, the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result. Before performing any maintenance, adjustment or service verify that ON/OFF switch on the joystick is in the OFF position. Installing/Removing/Using the Footrest/Legrest NOTE: For this procedure, refer to FIGURE 6.1. NOTE: This procedure applies to the swingaway footrest and elevating legrest. Installing 1. Turn the swingaway footrest assembly to the side (open footplate is perpendicular to wheelchair). 2. Install the hinge plates on the swingaway footrest assembly onto the hinge pins on the wheelchair frame. 3. Push the swingaway footrest assembly towards the inside of the wheelchair until it locks into place. NOTE: The footplate will be on the inside of the wheelchair when locked in place. 4. Repeat this procedure for the other footrest assembly. Removing 1. Push the footrest release lever inward. 2. Rotate swingaway footrest assembly outward. 3. Lift the swingaway footrest assembly off of the hinge pins. Using 1. To move the footrest out of the way without removing, push the footrest release lever inward, rotate footrest outward. 2. To lock the footrest, push the swingaway footrest assembly towards the inside of the wheelchair until it locks into place. Part No. 1118386 33 P9000™ XDT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
SECTION 6—FRONT RIGGINGS
Part No. 1118386
33
P9000
™
XDT
SECTION 6—FRONT RIGGINGS
±
WARNING
After ANY adjustments, repair or service and BEFORE use, make sure that all
attaching hardware is tightened securely - otherwise injury or damage may result.
While the wheelchair is moving, minimum ground clearance for the front rigging is
three inches. If the wheelchair is not moving, the front rigging MUST maintain a
minimum of one inch ground clearance - otherwise personal injury and damage may
result.
Before performing any maintenance, adjustment or service verify that ON/OFF
switch on the joystick is in the OFF position.
Installing/Removing/Using the Footrest/Legrest
NOTE: For this procedure, refer to FIGURE 6.1.
NOTE: This procedure applies to the swingaway footrest and elevating legrest.
Installing
1.
Turn the swingaway footrest assembly to the side (open footplate is perpendicular to
wheelchair).
2.
Install the hinge plates on the swingaway footrest assembly onto the hinge pins on the
wheelchair frame.
3.
Push the swingaway footrest assembly towards the inside of the wheelchair until it
locks into place.
NOTE: The footplate will be on the inside of the wheelchair when locked in place.
4.
Repeat this procedure for the other footrest assembly.
Removing
1.
Push the footrest release lever inward.
2.
Rotate swingaway footrest assembly outward.
3.
Lift the swingaway footrest assembly off of the hinge pins.
Using
1.
To move the footrest out of the way without removing, push the footrest release lever
inward, rotate footrest outward.
2.
To lock the footrest, push the swingaway footrest assembly towards the inside of the
wheelchair until it locks into place.